background image

26

04/12/2017

rev.02

Italia 

Use and maintenance manual

4    Intended use and installation location

The product is designed to protect against solar radiation and possibly to limit reverberation in the space below it.

Users of the product must be adults.

Improper use of the product shall release the Manufacturer from any liability from damage or injuries which might 

result.

Failure to respect the indicated conditions of use shall invalidate any and all warranties provided by the 

manufacturer.

The product, once installed, is intended only to perform raising or lowering of the fabric in order to reach the 

maximum opening and closing positions, as well as the intermediate ones if required.

· Before making the product operational, read Cap.2 “Safety”, pag.23 and Cap.4 “Intended use and 

installation location”, pag.26 carefully.

· Ensure there is nobody obstructing or excessively close to the product’s moving parts when opening 

and closing.

·  Pay  attention  to  all  the  warnings  applied  to  the  product,  and  follow  all  safety  regulations  and 

instructions for use.

· Any use other than those indicated above is forbidden, as different conditions of use could create 

risks to the user and other persons nearby.

· It is strictly prohibited to climb on or hang/place any objects from/on the product.

· The product must always be opened from top to bottom and never vice versa, as it could break with 

the risk of serious personal injuries.

· Close the product completely in the event bad weather or snow.

· The operation of the product with snow on the fabric or in freezing temperatures could damage it.

·  The  formation  of  condensation  on  the  fabric  should  not  be  considered  a  defect;  it  is  a  natural 

phenomenon.

Manual product

The product is opened and closed by a rod attached to a manual crank.

Motorized product 

The product can be opened and closed via:

· a SWITCH installed near the product in a position providing the user full visibility of the same during its movement. 

If installed outdoors, the switch must have appropriate ingress protection.

· A REMOTE CONTROL, portable or wall mounted.

The minimum installation height of the product should comply with applicable legislation; if fitted, the opening/

closing switch must be installed in a protected position, at a minimum, legal height from the ground and in an area 

which is not dangerous to access.

Fig. 6 

OPENING: Fabric stretched 

to its maximum extension. 

Fig. 7 

STOP: Stop of the move

-

ment. 

Fig. 8 

CLOSURE: Fabric wrapped 

around roller tube. 

See the instructions provided in the remote control manual annexed.

Summary of Contents for Italia













Reviews: