background image

Manual  

DISTRIBUTION AMPLIFIERS

Technical Support

[email protected]

1888-258-2028 / 1203-778-0295

HD View4

Customer Support

[email protected]

1718-796-7178 ext.23

Adjustments (on front
panel):

•  Independent gain con-
trol adjustment provided
for all four Output Groups
for all video signals
(YPrPb & Composite
Video) to compensate for
excessive cable lengths
up to 1000 feet
•  Sixteen, front-panel
adjustment potentiome-
ters
•  Adjustment procedure is
based on measured out-
put cable resistance
•  Each run of YPrPb
cable must be the same
length per output

Mechanical

•  Easy to install and inte-
grate -- Custom Installer’s
dream 
•  Connectors and cables
are all located on the rear
of the unit
•  All video and audio
inputs and outputs have
color-coded RCA female
connectors
•  5-pin DIN power con-
nector
•  Cable compensation
adjustment potentiome-
ters are on the front of the
unit
•  Rack mountable:  1U
•  Size:  17" x 8" x 1.5"
•  Weight:  4 lbs.
•  Enclosure type:  Metal
•  Input Power:  External
power supply provided,
110-240V AC, 50-60 Hz,
0.9A

Signal Properties:

•  All known video

formats are accepted

•  Output scanning

format is always the

SAME as the input

scanning format

•  Component Video 

•  Bandwidth -3 dB at 120

MHz, linear-phase pass-

band 

•  Unity-gain, 1 volt p-p, ter-

minated to 75 ohms

•  Composite sync on "Y"

channel

•  Audio 

•  Bandwidth flat 20 Hz to 50

MHz

•  Analog (standard line-type Left &

Right pairs) or digital PCM audio

•  Digital PCM audio

Modes of Operation:

•  You must set the six 8-bit DIP

Switches as described in the

Operation Manual to the desired

Operating Mode

•  ADA4 Mode:

•  Distribution of your YPrPb and

Left & Right analog or digital

PCM audio inputs to as many as

four separate Component Video

monitors

• Distribution of your YPrPb and

Left & Right analog audio and

Composite Video (CV) inputs

simultaneously to as many as

four separate Component Video

and Composite Video displays

•  PCMD4 Mode:

•  Distribution of your single digital

PCM audio input to as many as 24

separate destinations

•  Distribution of your single

Composite Video (CV) input to as

many as 24 separate destinations

Summary of Contents for HD View4









Reviews: