KDF Neo Super Cascom Instruction Manual Download Page 8

Page: 8 / 25

- 6 -

FUSE

Vacuum Pump Power Outlet

Vacuum Pump Fuse

Argon Gas Hose Inlet

Drain Filter

Power Cord

Vacuum Pump Hose Inlet

Compressed Air Inlet

Exhaust Air Filter

Back View Parts

●

and Descriptions

Exhaust Air Filter A port to release pressure from chamber when you perform casting.

P18

Periodic cleaning is recommended.

→

Drain Filter

Used to prevent rust, dust, moisture etc. out of compressor from entering the

P19

unit. Periodic cleaning is recommended.

→

Compressed Air Inlet

Connect one end of the air hose provided and the other end to the nearby

compressed air source.

→

Argon Gas Hose Inlet

Connect the hose provided to a low pressured argon gas tank with a gas

regulator for argon pressure and argon melting atmosphere.

→

If argon pressure and argon melting atmosphere is not going to be used, then the

connection is not necessary.

Vacuum Pump Hose Inlet

Used to connect a hose to vacuum pump optional .

(

)

→

Vacuum Pump Fuse

A fuse against over power flow to vacuum pump optional .

(

)

Vacuum Pump Power

Power outlet for vacuum pump optional .

(

)

Outlet

Power Cord

Main power cord for the unit. A dedicated power outlet with grounding is
recommended to use.

Summary of Contents for Neo Super Cascom

























Search results

Summary of Contents for Neo Super Cascom

Reviews:

Related manuals for Neo Super Cascom

Brands by name

Popular brands

KDF Neo Super Cascom, Instruction Manual

Search results

Summary of Contents for Neo Super Cascom

Reviews:

Related manuals for Neo Super Cascom

Brands by name

Popular brands