background image

 

 
 

 

REV 1.0.8 (Last Modified March 1, 2021) 

1 | 30    

R E V 1 . 0 . 8

 

 

 
KDE Direct, LLC. License Agreement 

PLEASE READ THIS LICENSE AND MANUAL IN THEIR ENTIRETY BEFORE USING THE KDE UVC SERIES ESC AND/OR KDECAN PROTOCOL.  
BY  USING  THE  KDE  UVC  SERIES  ESC  AND/OR  KDECAN  PROTOCOL,  YOU  ARE  ACKNOWLEDGING  THAT  YOU  HAVE  READ  AND 
UNDERSTOOD THE CONTENT, INCLUDING ALL WARNINGS AND DISCLAIMERS CONTAINED HEREIN.  YOU FURTHER ACKNOWLEDGE 

THAT YOU HAVE READ AND UNDERSTOOD ALL KDE POLICIES REFERRED TO IN THE MANUAL, INCLUDING KDE’S LIABILITY POLICY 

AVAILABLE A

http://www.kdedirect.com/pages/liability-policy

 IF YOU DO NOT UNDERSTAND ANY OF THE WARNINGS AND/OR 

DISCLAIMERS, DO NOT USE THE KDE UVC SERIES ESC AND/OR KDECAN PROTOCOL.  

KDE DIRECT RESERVES THE RIGHT TO CHANGE OR MODIFY THE TERMS OF THE LICENSE AND MANUAL AT ANY TIME WITHOUT PRIOR 
NOTICE.  

1. General.  

The KDECAN Protocol Software (defined herein) is designed to enable functionality between KDE UVC Series ESC to your 

third party controllers.  This document provides general recommendations to enable functionality between the KDE UVC Series ESC 
and your third party controller.   

As detailed below, KDE Direct, LLC. (“KDE Direct”) does not manufacture this third party product and therefore does not suppo

rt or 

warranty the safety, use, functionality or compatibility of any third party controllers.  Any information as to a third party controller is 
provided solely as a reference.  Please refer to documentation accompanying your third party controller and any updates issued by 
the third party controller manufacturer for best practices and/or other information related to the safety, use, functionality or capability 
of your controller.   

2. 

Intellectual  Property.

    The  KDECAN  Protocol  Software,  documentation,  images,  content,  interfaces,  fonts  and  any  other  data 

accompanying this License whether pre-installed on the KDE UVC Series ESC hardware, on disk, in read only memory, on any other 

media or in any other form (“KDECAN Protocol Software”) are licensed, not sold, to you by KDE Direct for use only under the t

erms of 

this License.  KDE Direct retains ownership of the KDECAN Protocol Software itself and reserve all rights not expressly granted to you.  
The  terms  of  this  License  will  govern  any  software  upgrades  provided  by  KDE  Direct  that  replace  and/or  supplement  the  original 
KDECAN Protocol Software, unless such upgrade is accompanied by a separate license in which case the terms of that license will 
govern. 

Title and intellectual property rights in and to any content displayed by or hardware accessed through the KDECAN Protocol Software 
belongs to the respective owner.  Such content or hardware may be protected by copyright or other intellectual property laws  and 
treaties, and may be subject to terms of use of the third party providing such content.  This License does not grant you any rights to 
use such content or hardware nor does it guarantee that such content or hardware will continue to be available to you.  

3. 

License Uses and Restrictions.   

The Software is licensed to you and not sold.  Subject to the terms of this Agreement, KDE DIRECT 

hereby grants you a personal, non-exclusive, non-transferable, non-sublicensable, and revocable license to use the Software solely in 
connection with the related program output for which the software was designed, specifically, with third party controllers. 
You acknowledge that the Software is protected intellectual property and KDE DIRECT reserves all such rights with respect to  the 
Software, except for the license expressly granted to you in this Agreement.  Except for such express license, no right, title, interest or 
license in or to the Software, whether by implication, estoppel or otherwise, is granted, assigned or transferred to you.  You agree not 
to take any action that interferes, in any manner, with KDE DIRECT or any of it

s authorized licensor’s rights with respect to the Software.  

In addition, title, ownership rights and intellectual property rights in and to any content accessed through the Software is the property 
of the applicable content owner and may be protected by applicable copyright, patent, trademark or other law.  This Agreement gives 
you no rights to such content. 

You acknowledge and agree that you will not: (a) reproduce the Software; (b) modify, adapt, translate or create any derivative works 
of the Software; (c) attempt to circumvent or disable the Software or any technology features or measures in the Software by any 

Summary of Contents for KDE-UAS40UVC































Reviews: