KBL megaSun 5800, Operating Instructions Manual

Page: 10 / 60

O p e r a t i n g I n s t r u c t i o n s | KBL 5800
10
Connections
Connecting the mains voltage
DANGER!
Live components
Risk of fatal injury due to electric shock
when touching live parts.
- Switch off mains voltage.
- Protect against re-connection.
Both the power supply and the related connection
work must comply with national standards. The
connection work must only be performed by qualifi ed
expert staff. The connection to the 3 x 220 V mains
must be protected by fuses. Their specifi cations are
listed in the chapter “Technical data”.
A Class-A ground fault circuit interrupter (GFCI) has
to be used for Canada.
Should the operation of the tanning unit cause any
interference in the power supply network, e.g. with
ripple-control systems (TRA), consult your power
supply company to have corresponding blocking
elements (audio frequency suppressors) installed.
Figure 10.1
The tanning device is by default set up to operate
on 3 phases but it can be changed over to 2-phase
operation. The wiring for 3-phase operation is shown
below:
Figure 10.2
X5.8
X0.N3
F2.A
K2.5
K1.5
K2.3
K1.3
K2.1
K1.1
F1.A
L2(S)
L3(T)
L1(R)
D
A
B C
X2.9
gnd
X4.3
X2.1 X4.1
X4.2
X7.3
X1.9
CA
X5.6
X2.4
X2.2
X2.3
X0.L3
E2.3
X2.5
b ase
X0.N1
X0.N2
K 6 .A2
F1.D
X1.8
X8.1
K1.5
K2.5
L
2
L
3
PE
PE
L
1
L
2
L
3
N
2
N
3
N
4
N
5
N
6
N
7
1
L
1
N
1
Mains 3 x 220V / 60Hz
The wiring for 2-phase operation is shown below.
1. Re-wire the 3 cables according to the diagram.
2. Make sure that you use the right cable for the
power supply.
Figure 10.3
jumper settings
change connections
s e t j u m p e r
X0.L3
X2.3
X2.2
X2.4
X5.6
CA
X1.9
X7.3
X4.2
X4.1 X2.1
X4.3
X5.8
X2.5
E2.3
b ase
K1.5
K2.5
F2.A
K1.3
K2.3
X0.N2
X0.N1
X0.N3
K1.1
K2.1 F1.A
L1(R)
D
A
B C
X2.9
gnd
K 6 .A2
F1.D X1.8 X8.1
L2(S)
(K 1 . 5 ) - from[X0.L3D]to[X0.L2C]
(K 2 . 5 ) - f ro m [ X 0 . L 3 D]to[X0.L2C]
(X0.N1) - from[X0.L1C]to[X0.L3D]
K2.5
K1.5
from [X0.L1]to[X0.L2]
W a g o i t e m n r . 2 0 1 6 - 4 0 2
K B L i t e m n r. 3 2 0 0 4 5 3 5 2 0
(X0.N2) - from[X0.L2C]to[X0.L3D]
N
4
N
3
N
1
N
7
N
6
N
5
N
2
L
3
L
2
PE
PE
L
1
L
1
L
2
L
3
1
change connections
1 (K2.5) > from [X0.L3D] to [X0.L2C]
2 (X0.N1) > from [X0.L1C] to [X0.L3D]
3 (K1.5) > from [X0.L3D] to [X0.L2C]
4 (X0.N2) > from [X0.L2C] to [X0.L3D]
set jumper
5 from [X0.L1] to [X0.L2]
----------------------------------
Wago item Nr.: 2016-402
KBL item Nr.: 3200453520
Mains 2 x 220V / 60Hz