![background image](http://html1.mh-extra.com/html/kawneer/1686/1686_installation-instructions_3676056003.webp)
kawneer.com
Kawneer r
eserves the right to change configuration without prior notice when deemed
necessary for pr
oduct impr
ovement.
© Kawneer Company
, Inc., 2011
Laws and building and safety codes gover
ning the design and use of glazed
entrance, window
, and curtain wall pr
oducts vary widely
. Kawneer does not contr
ol
the selection of pr
oduct configurations, operating har
dwar
e, or glazing materials,
and assumes no r
esponsibility ther
efor
.
EC 97904-36
3
1/32"
1/32"
400020
400079
450020
450079
451020
451079
0.874
0.719
R0
.15
6
0.
56
2
0.
97
6
1.156
0.437
0.
28
1
0.874
0.719
R0
.15
6
0.
56
2
0.437
0.
28
1
C/L OF TRANSOM BAR
0.874
0.719
R0.1
56
0.
56
2
0.437
0.
28
1
0.
97
6
1.156 1.156
HEADER \ T-BAR
0.874 0.719
0.
56
2
0.437
0.
28
1
0.874
0.719
0.
56
2
0.437
R0
.15
6
TY
P
0.
28
1
C/L OF THRESHOLD
2.
00
0
1.156
1.156
0.874
0.719
0.
56
2
2.
00
0
069139
069143
1.156
0.437
R0
.15
6
0.
28
1
FEBRUARY, 2011
KAWNEER 1686 CONCEALED EXIT DEVICE
INSTALLATION INSTRUCTIONS (PART NUMBER 038-310)
FINAL ASSEMBLY:
1) Slide pivot stile filler into device, attach pivot stile end cap with fasteners provided.
2) Slide lock stile filler into device, install cover over brackets on lock stile and attach with fasteners provided.
3) Stand door in the vertical position and place on blocks to test operation.
Note: The top and bottom bolts should extend approximately 1/2" beyond door stile.
4) Depress push bar, the top bolt should lock in the retracted position. If locking does not occur readjust top bolt with half turn increments until
locking occurs.
Note: Bottom bolt should be flush with end of stile to approximately 1/16" projection beyond the end of the stile in the retracted position.
5) Release the bolts by depressing the trigger at the top guide.
EXTERIOR CYLINDER DOGGING:
1) Insert dogging key, turn key counterclockwise until rods are retracted. Top bolt should lock into retracted position.
2) Return key to vertical position.
3) With rods in the retracted position, turn key clockwise approximately 1/8 of a turn to activate dogging.
4) Return to vertical position and remove key.
5) Turn key counterclockwise to the unlock position to release exterior key dogging, remove key.
TOP BOLT FABRICATION:
1) Fabricate header\t-bar for top bolt cutout as indicated below, for single or pairs of doors.
BOTTOM BOLT FABRICATION:
1) Fabricate threshold for bottom bolt cutout as indicated below,
for single or pair of doors.
DOOR STOP INSTALLATION:
Using 033-981 threshold stop package as a template,
drill (2) 5/32" (0.156) diameter holes and secure
with self threading fasteners.
Approximately
SINGLE DOOR
(R.H. Shown)
PAIR OF DOORS
SINGLE DOOR
(R.H. Shown)
PAIR OF DOORS
Approximately