background image

Instructions for use K-ERGOgrip 4944
1 User instructions | 1.4 Transportation and storage

6 / 30

5. Report the damage to KaVo.

6. Consult with KaVo first, before returning a damaged product.

7. Send the signed delivery receipt to KaVo.

If the product is damaged but there was no discernable damage to the packaging

upon delivery, proceed as follows:

1. Report the damage to the shipping company immediately and no later than 7 days

after delivery.

2. Report the damage to KaVo.

3. Leave the product and packaging in the condition in which you received it.

4. Do not use a damaged product.

Note

If the recipient fails to comply with any of the above-mentioned obligations, the

damage will be considered to have arisen after delivery

(in accordance with the General German Freight Forwarders´ Terms and Conditions, Art. 28)

.

Outside Germany

Note

KaVo shall not be held liable for damage arising from transportation.
The shipment must be checked on arrival.

If the packaging is visibly damaged on delivery, please proceed as follows:

1. The recipient of the package must record the loss or damage on the delivery re‐

ceipt. The recipient and the representative of the shipping company must sign this

delivery receipt.

 

Without this evidence, the recipient will not be able to assert a claim for damages

against the shipping company.

2. Leave the product and packaging in the condition in which you received it.

3. Do not use the product.

If the product is damaged but there was no discernable damage to the packaging

upon delivery, proceed as follows:

1. Report any damage to the shipping company either immediately or no later than 7

days after delivery.

2. Leave the product and packaging in the condition in which you received it.

3. Do not use a damaged product.

Note

If the recipient fails to comply with any of the above-mentioned obligations, the

damage will be considered to have arisen after delivery

(in accordance with CMR law, Chapter 5, Art. 30).

1.4.3 Information on the packaging: Storage and transportation

Note

Please keep the packaging in case you need to return the product for servicing or

repair.

The symbols printed on the outside are for transportation and storage, and have the
following meaning:

Summary of Contents for K-ERGOgrip 4944































Reviews: