background image

1 / 8

EXD 154

2050000003

Sat-IF Distribution System (4 x Sat-IF)

Digital Wideband Multi-switch

About This Manual

This document is part of the product.

Do not install or use the device until 

you have read and understood this 

document.

Keep this document for reference 

throughout the service life of the device 

and pass it on to any new owner or 

user.

For the most up-to-date version of this 

document, go to 

www.kathrein-ds.com

.

Features

Universal multi-switch with automatic 

operating mode detection. A standard TV or 

16 receivers each can be operated in single 

cable mode at each connection.

All types of signalling are supported and 

automatically detected: 14/18 V 0/22 kHz 

(legacy), DiSEqC™ 1.0, single cable stan-

dards according to EN 50494, as well as the 

extended command set according to EN 

50607 (SCD2 or JESS); PIN codes can also 

be used in single cable operation.

Latest IC technology with full band captu-

ring ensures the best signal quality. The 

inputs are broadband and can also be 

operated with wideband LNBs (e.g. UAS 

582). This means that a multi-feed system 

can be implemented (for two LNBs, the TV 

set must support either DiSEqC™ or the 

single-cable standard).

QR code for user instructions

For indoor installation

The integrated AGC (Automatic Gain 

Control) ensures that the Sat IF signals 

have a constant output level and more 

reserve in the distribution.

suitable for DVB-T/T2

When all TV sets/receivers are switched 

off , the multi-switch no longer consumes 

any power. If Kathrein Power Saving is acti-

vated, the LNBs are also switched off .

The integrated power unit for supplying the 

LNB is highly effi  cient and short-circuit-

proof.

Wideband to Quatro mode:

In this case, the two inputs of the wideband 

LNB are permanently connected to the four 

outputs of the multi-switch. The outputs of 

the EXD 154 behave like a Quatro LNB, so 

that an additional standard multi-switch 

can be connected.

EXD 154

230V~  50

-

60Hz  17W

2050000003

2

4

1

3

V

 low

V

 high

H

 high

T

err.

H

 low

18V

300mA max.

Power 

Saving

Wideband

Universal

Wideband

Universal

ON

OFF

WB-Quatro

177

215

42,5

134

148

Tip

The QR code on the front of the 

multi-switch will take you to our 

website where you can download 

these instructions:

Summary of Contents for EXD 154









Reviews: