background image

3 / 8

Safety Precautions

    

Current-carrying device

Do not open or tamper with the unit

Always disconnect the mains plug from the socket when working on the 

system

Ensure adequate clearance: at least 5 cm to all sides

Do not install on the ceiling or vertically

Ensure free circulation of air to dissipate the heat from the unit. Risk of 

overheating!

Admissible ambient temperature: -20 to +40 °C

Note:

Do not place any liquid-fi lled items on top of the device

Do not expose the device to dripping or splashing water

The mains plug must be easily accessible and usable 

The device is only safely and completely disconnected from the mains by 

pulling the mains plug

SAT-IF Distribution Equipment 

(not for wideband operation!)

Type

Kathrein Power Saving

Switch Setting

VWS 2551

Amplifi er

Unrestrictedly usable

ON

EBX 2520

Two-way splitter

Unrestrictedly usable if each trunk 

is terminated by the Kathrein Power 

Saving-capable end multi-switch 

ON

EAX 2512

Two-way tap

Not Kathrein Power Saving-capable

OFF

VWS 2500

Amplifi er

Order no. 20510098 is Kathrein Power 

Saving-capable; older models are not

ON / OFF

To prevent the set user band from being used or disturbed by another subscriber, the 

user band can be protected by means of a PIN code. The PIN code must be entered in the 

settings of the receiver/TV. Each user band is assigned a fi xed PIN.

PIN Code Protection

UB 

1

UB 

2

UB 

3

UB 

4

UB 

5

UB 

6

UB 

7

UB 

8

UB 

9

UB 

10

UB 

11

UB 

12

UB

13

UB

14

UB 

15

UB

16

151 052 133 124 205 196 187

178 099 232 198

111

190 002 201 140

Summary of Contents for EXD 154









Reviews: