background image

RM-100 FLOOR MOUNT MANUAL

16

You can often repair failed equipment at a lower cost than replacement. Kasco Marine estimates repairs 
at the request of the customer. This request should include a daytime phone number and e-mail address.

Estimate options are as follows:

• 

 Kasco contacts the customer with a repair total after we evaluate the unit, but before we perform the 
work quoted.

• 

 Customer pre-approves repair of the unit if costs are below a stated dollar amount. Example: “Please 
repair if total is under $150.00 before shipping charges.”

Kasco will recycle any unit we receive for estimate but which the customer declines to repair, unless the 

customer specifies otherwise. If the customer would like the product returned, Kasco will return the unit 

to the condition in which we received it, and we will ship it at the customer’s expense.

Billing

Contact Kasco to arrange payment for any non-warranty repairs. We will request payment information 
upon customer approval of the estimate.

NON-WARRANTY REPAIRS

715.262.4488

Kasco Marine
800 Deere Road
Prescott, WI 54021

kascomarine.com  |  [email protected]

CONTACT US

®

Certified to

NSF/ANSI 61 & 372

Back to Contents

Summary of Contents for CERTISAFE RM-100



















Reviews: