Kargo Master 4A96L Instruction Manual Download Page 11 | Manualshive

Page: 11 / 19

background image

Instructions – 4A96L

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST)

Page 10



Place rear pan on top of wheels and bow. Be sure the wheel caps DID NOT come off.



Align the arms from the pan with the holes in the damper mechanism where the bolts were previously
removed.



Bolt together using previously removed hardware. Only mount the front two bolts, leaving the holes to
the rear as shown empty. The empty holes are for the handle installation.



Snug tighten, but allow movement.

«
...
9
10
11
12
13
...
»

Summary of Contents for 4A96L




















Reviews:

No comments

Related manuals for 4A96L

Brand: Hanwha Vision Pages: 2

Brand: vogel's Pages: 13

Mountlogic BT8223

Brand: B-Tech Pages: 20

Brand: Sealey Pages: 2

Brand: WAC Lighting Pages: 2

Brand: Aruba Networks Pages: 8

Retroverb Lancet

Brand: Vermona Pages: 23

Brand: HAGOR Pages: 12

Brand: AAVARA Pages: 34

Brand: PEERLESS Mounts Pages: 8

Universal Slat Wall Multi Arm Mount KSY220

Brand: CHIEF Pages: 10

SCREEN BUDDY SBUDDYM16

Brand: Sandstrom Pages: 12

Brand: Teledyne Lecroy Pages: 8

Brand: Schmidlin Pages: 12

Brand: Detex Pages: 7

Brand: Innovative Pages: 2

PTS-04-M400/MX915

Brand: Innovative Pages: 9

Brand: Innovative Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands