![background image](http://html2.mh-extra.com/html/karcher/t-racer-t-400/t-racer-t-400_instructions-manual_3692542007.webp)
English
7
eg: K 6.50 – K 7.91, Kärcher 600 – Kärcher 770
Î
Use yellow high-pressure nozzles.
Note:
The yellow high-pressure nozzles
have already been installed.
eg: K 2.00 – K 5.91, Kärcher 201 – Kärcher 560
Î
Use grey high-pressure nozzles.
Î
Illustration
1 Remove the clip.
2 Pull out the yellow high-pressure nozzle.
3 Insert the grey high-pressure nozzle.
4 Re-insert the clip.
Note
: Always use Kärcher water filter (order no.
4.730-059.0) during suction operations of the
high-pressure cleaner.
Fasten the T-Racer to the high-pressure gun us-
ing the extension pipes.
Î
Illustration
1 Screw the two extension pipes together.
2 Press the extension tube into the bayonet
connection of T-Racer, then turn by 90° until
it locks into place.
Tighten the safety cover.
3 Press the extension tube into the bayonet
connection of the high-pressure gun, then
turn by 90° until it locks into place.
Tighten the safety cover.
몇
Caution
Î
Illustration
–
Do not run over free-standing corners!
–
The T-Racer is not suited for scouring or
scrubbing!
– Outdoor surfaces should be swept before
the T-Racer is used to avoid damaging the
high-pressure nozzles.
Î
Adjust the turning hande "power" as per the
surface to be cleaned
Fasten the T-Racer directly to the high-pressure
gun.
Î
Illustration
– Press the bayonet connection of the T-Racer
into the connection of the high-pressure gun,
then turn by 90° until it locks into place.
– Tighten the safety cover.
Caution
Î
Illustration
Always hold the T-Racer at the handle while
cleaning the walls.
Î
Adjust the turning hande "power" as per the
surface to be cleaned
The turning handle "power" is used to change
the distance of the high-pressure nozzles to the
surface to be cleaned.
Robust surfaces
(for e.g. tiles, concrete, stone)
Î
Illustration
Set turning handle "power" to "MAX".
For the effective cleaning of hard-to-remove
contamination.
Sensitive surfaces
(for e.g. wood)
Î
Illustration
Set turning handle "power" to "MIN".
For the gentle cleaning of sensitive surfaces.
Î
Illustration
For normal surface cleaning, press the foot
pedal for surface cleaning.
A water stream will be emitted from the two
high-pressure nozzles in the rotor arm.
Î
Illustration
For edge and corner cleaning, press the foot
pedal for edge cleaning.
A water stream will be emitted from green
high-pressure nozzle.
You can use the extension pipes with any other
Kärcher accessory.
High-pressure cleaner does not build up the
pressure or is vibrating
.
Î
Dismantle the high-pressure nozzles, check
the high-pressure nozzles for damage, rinse
the T-Racer with clean water then reinstall
the high-pressure nozzles.
High-pressure cleaner with nominal pressure
(p) of 13 MPa (130 bar) to 16 MPa (160 bar)
High-pressure cleaner with nominal voltage
(p) lesser than 13 MPa (130 bar)
Installing the nozzles
Application
Cleaning floor surfaces
Cleaning wall surfaces
Control elements
"Power" turning handle
Foot pedal for surface cleaning
Foot pedal for edge cleaning
Tip
Troubleshooting