– 4
ote:
The predefined order during com-
missioning must be strictly observed. Oth-
er ise it is not guaranteed that the sensor
is correctly registered ith the control unit.
Assistance for the operating procedure is
provided by the accompanying uick start.
ote:
The battery is not included in the
scope of delivery.
Î
Figure 1, 2
Insert the battery into the battery com-
partment in the correct position (+/-
marking).
As soon as the battery is inserted, the
display, after a short self-test, changes
directly into the settings mode for the
current time. The hours of the time dis-
play are flashing.
Î
Figure 3
Set hours.
Î
Press the
OK button
and set minutes.
Î
Confirm the setting of the minutes by
pressing the
OK button
.
ote:
From no on, the receiver aits for
the radio signal of the sensor for teaching.
During this time, the radio signal is flashing
and the seconds countdo n is counted
do n.
Important:
In order to establish the radio
contact bet een the receiver and the sen-
sor, the sensor battery must be inserted
ithin 60 seconds.
!
CAUTION
The moisture absorption of the sensor pad
can be impaired by grease or oil on the sur-
face. Do not touch or wipe the sensor pad
with greasy/oily hands/rags.
Î
Figure 4
Remove the sensor cap of the sensor.
Î
Connect the battery ith the battery
clip. The connected battery is reinsert-
ed in the casing ith the battery clip go-
ing in first.
Î
Close the sensor by means of the sen-
sor cap.
Î
Figure 5
Contact radio signal.
As soon as the contact of the radio sig-
nal is established, the symbol for the ra-
dio signal appears permanently. It is
no guided through the setup se-
uence (preset value for moisture,
times, etc.).
Î
Figure 6
Sensor 1 as detected successfully.
ote:
The operating mode is specified and
saved during the teaching process. A
change of the operating mode (e.g. from
sensor control to time control) is only possi-
ble by a ne teaching process after a reset.
Î
Figure 7
Set the tripping limit for the soil moisture.
ote:
Setting is only possible in the sen-
sor-controlled operation, not in the time-
controlled operation.
Drops sho the measured soil moisture,
the adjustable triangles sho the tripping
limit. As soon as the measured soil mois-
ture falls belo the tripping limit, the irri-
gation starts automatically at the next set
time.
Î
Figure 8.1, 8.2
Set the irrigation time for mornings and
evenings.
Per day 2 times can be set at hich the
irrigation starts if the measured soil mois-
ture is belo the tripping limit. With
- -:-
-
the irrigation time can be deactivated.
Î
Figure 9
Set the irrigation duration.
The irrigation duration per irrigation cycle
can be set bet een 1 - 90 minutes. With
- -
the irrigation duration is deactivated.
Î
Figure 10
Set the irrigation delay.
The irrigation can be delayed for 1 - 7
days this stimulates the root develop-
ment of the plants. Moreover, it saves
ater if it rains during the delay days.
With setting
- d
this function is deactivated.
reparation control unit
reparation / teaching sensor 1
Irrigation settings of water outlet 1
14
EN
Summary of Contents for SensoTimer ST6 eco!ogic
