8
English
Disconnecting accessories
1. Set the selector switch for the steam volume to the
rear.
The steam lever is locked.
2. Push the unlocking button and pull the parts apart.
Illustration L
Operation
Filling water
Note
Warm water reduces the heating-up time.
Note
Descaling the steam boiler is not required if commer-
cially available distilled water is used.
1. Unscrew the safety lock.
Illustration B
2. Drain the water completely out of the steam boiler.
Illustration P
3. Fill a maximum of 1 litre distilled water or tap water
into the steam boiler.
Illustration B
4. Insert the safety lock.
Illustration C
Switching on the device
1. Place the device on a firm surface.
2. Insert the mains plug into a socket.
Illustration D
The LED light is lit in red.
3. When the LED light lights up green, the device is
ready for operation.
Illustration E
4. Press the steam lever.
Illustration F
Steam leaks out.
Regulating the steam volume
Note
The device heating always switches on again during
use to maintain the pressure in the steam boiler. The or-
ange indicator light - heating illuminates to indicate this.
The expelled steam volume is regulated using the se-
lector switch for steam volume. The selector switch has
3 positions:
1. Set the selector switch for the steam volume to re-
quired steam volume.
2. Press the steam lever.
3. Before starting cleaning, point the steam gun at a
cloth until steam is expelled evenly.
Refilling water
If the steam volume is reduced during work or if no more
steam volume comes out, the water will have to be re-
filled.
1. Switch the device off; see Chapter
2. Unscrew the safety lock.
3. Fill a maximum of 1 litre distilled water or tap water
into the steam boiler.
4. Insert the safety lock.
5. Insert the mains plug into a socket.
6. Wait until the LED light has changed from red to
green.
The device is ready for use.
Switch off the appliance
1. Pull the mains plug out of the socket.
2. Press the steam lever until no more steam flows out.
Illustration M
The steam boiler is depressurised.
3. Set the child lock (selector switch for steam volume)
to the rear.
The steam lever is locked.
Rinsing out the steam boiler
Rinse the appliance’s steam boiler after max. every
tenth boiler fill.
1. Switch the appliance off, see Chapter
.
2. Allow the appliance to cool down.
3. Disconnect the accessory.
4. Fill the steam boiler with water and swing it around
vigorously. Lime residue which has been deposited
on the bottom of the steam boiler will be released as
a result.
5. Drain the water completely out of the steam boiler.
Illustration P
Store the device
1. Hang the floor nozzle in the park bracket.
Illustration N
2. Wind the steam hose and mains connection around
the carrying handle or device and/or insert the
steam gun in the ground floor nozzle.
Illustration O
3. Insert the extension tube in the large accessory
holder or allow to dry and store in the accessory
bag.
Illustration O
4. Allow the rest of the accessories to dry and then
store in the accessory bag
Illustration O
5. Store the device in a dry location that is protected
from frost.
ATTENTION
Material damage due to a stuck safety lock
If the safety lock is not removed after cleaning, there is
a possibility that the lock could get stuck in the thread.
After cleaning, unscrew the safety lock and store it, for
example, with the other device accessories.
Important application instructions
Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning
it before using the appliance. In this way the floor will be
cleared of dirt and loose particles before the wet clean-
ing.
Freshening up textiles
Prior to using the appliance, always check the compati-
bility of the textiles at a concealed point: Steam down
Maximum steam volume
Reduced steam volume
No steam - child lock
Note
In this position, the steam lever cannot
be operated.
