38
English
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2019/11/01
1.8
Manual suction hose attachment (ex-
factory)
The manual suction hose is included in the scope of deliv-
ery when ordered ex-factory.
1
Manual suction hose
2
Manual suction pipe
3
Clamp lock belt
4
Locking wedge
5
Lynch pin
6
Locking hook
●
Removing the attachment from the vehicle
The attachment can be easily removed if not required.
To remove, pull out the lynch pin and open both locking
wedges. Then remove the attachment with 2 people.
●
Pivoting the attachment to the side
The attachment must be pivoted completely outwards in
order to empty the waste container.
To do this, open both locking wedges and pivot the at-
tachment all the way out to the side wall, where it is held
by a magnet. Push the locking hook upwards before piv-
oting back.
1.8.1 Working with the manual suction hose
The vehicle is parked and the travel direction selector
switch is in the NEUTRAL position (middle position).
1
Bottom rubber flaps position
Note
Working with the manual suction hose
2
Air intake opening
1. Lift the waste container until the rubber flaps can be fold-
ed down.
2. Fold the rubber flap down over the suction opening.
3. Lower the waste container again.
4. Open the clamp lock belt and remove the manual suc-
tion hose with the manual suction pipe from the storage
compartment.
1
Flap
2
Connection for water hose
3
Manual suction hose connection
5. Open the flap on the desired side.
6. Insert the manual suction hose into the connection
opening and turn it (bayonet).
7. Plug in the water hose if necessary.
8. Switch on the work hydraulics (PTO).
9. Switch on the blower via the switch (control console).
10.Deactivate the seat contact switch (F4 button on the
display).
11.Work with the manual suction hose.
12.After finishing work:
a Switch off the work hydraulics.
b Activate the safety contact switch.
13.Place the suction hose with the suction pipe in the stor-
age compartment and secure with the clamp lock belt.
1
Top rubber flaps position
Note
Normal sweeping
2
Air intake opening
14.Lift the waste container and fold up the rubber flaps.
15.Lower the waste container.
Summary of Contents for MC 250
