background image

9

Important Trailer Safety Information

Add the missing pounds of air pressure to each tire that 

is under inflated.
Check all tires to make sure they have the same air 

pressure.
If you have been towing your trailer and think that a tire 

is under inflated, fill it to the recommended cold inflation 

pressure indicated on your trailer's tire label placard or 

the VIN label. You can also check the sidewall of the 

tire for a correct tire inflation pressure. Your tire will 

have a slightly lower air pressure because the tire is 

warm when you are inflating it, but it will be much better 

than to continue to tow it with the under inflation it may 

have had. Once the trailer has been parked long 

enough to allow the tires to cool down, recheck the tire 

pressure and add additional air to return the tire 

pressure to the recommended level.

Tire Size

To maintain the trailer's carrying capacity and safety, 

purchase only the same size tires as what were origi

-

nally supplied on the trailer.

Safety Tips

Slow down if you have to go over a pothole or other 

object in road.
Do not run over curbs and try not to strike the curb 

when parking.
For a free brochure visit: 
www. nhtsa.dot.gov

IMPORTANT: Before towing this trailer be sure to 

read the instructions and warnings supplied in this 

manual. Also read the information supplied with 

your tow vehicle so you know and understand it's 

limitations.

Never Tow the Trailer Before Checking:

Coupler and latch assembly show no signs of 

wear or damage. 

Coupler hitch and hitch ball are of the same  

size.

Coupler and safety chains are safely secured to 

the hitch. 

Check all fasteners for proper tightness.

Load is securely tied down to the trailer.

Wheel lug nuts are properly tightened to the 

right torque. 

Wheel bearings are properly adjusted and 

maintained. 

Load is within the maximum load carrying 

capacity of trailer. 

Tires are properly inflated and are road worthy.

All trailer lighting is working properly.

Tire pressure and tire condition

Wheel lugs*

Bearing lube and tightness

Hitch

Safety chains

12V running lights

Distribution and security

Caster up in travel position

* Check lug nuts for tightness before initial trip, at 10 

miles, 25 miles and 50 miles. Recheck every 3 months 

or 3000 miles.

NOTE: Checking all of the above steps before every 

trip is key for safety.

IMPORTANT: The load must be distributed equally 

on the bed of the trailer if possible. Heavy, concen

-

trated loads may cause damage or possible failure 

of the trailer.
WARNING: Loads place on the trailer must be 

securely tied to the trailer. Always use appropriate 

tie downs designed to restrict loads from moving 

when properly attached. Failure to do so will allow 

shifting of the load causing potential trailer failure 

and/or loss of the load and personal injury.

This trailer is equipped to meet all applicable federal 

safety standards in effect the day of manufacture. 

Check local and state requirements regarding any addi

-

tional equipment that may be required.
The addition of optional equipment to your trailer may 

in- crease the total weight of your trailer package to 

where it now exceeds the maximum load carrying 

capacity of the trailer.

Landa ECOS 7000  Operator’s Manual  9.801-316.0 - E

Summary of Contents for LANDA ECOS 7000 Series







































Reviews: