-
6
Both waste containers are equipped with a
safety installation that switches off the run-
ning device when it is opened and issues a
warning message on the display.
The high emptying system is equipped with a
safety installation that blocks the sweeping
operation during the emptying procedure.
Appliances with a high emptying system
are equipped with a button for two-hand op-
eration.
For emptying the waste container, the
button must be pressed together with
the keys of the high emptying system.
During any work underneath the lifted
waste container, the lifting cylinder must be
secured by means of a safety support.
The safety support is attached to the cross-
beam by means of 2 star screws for stor-
age.
Remove safety support, in order to do
this, unscrew 2 star screws.
Insert safety support into the piston rod
for the lifting cylinder and secure it.
Note
: The round notch must point up-
wards.
The appliance is equipped with an auto-
matic parking brake that is integrated in the
front-wheel drive.
The parking brake takes effect as soon as
the device comes to a standstill and the ac-
celerator pedal is released.
The cover with the seat can be removed
for repair or maintenance work.
Prior to removing the cover, disconnet
the electrical socket plug connection of
the seat contact switch.
ATTENTION
The left cover may only be opened when
the programme selector switch is in the
"OFF" position and the key (Intelligent Key)
is removed.
Opening the left cover during operation of
the device is prohibited.
Grab the front of the cover on the re-
cessed grip, unlock it towards the top
and swivel it to the side.
Note
: The cover is equipped with a safety
installation that switches off the drive when
it is opened and issues a warning message
on the display. If the cover is not properly
closed the device will not operate.
If a warning message is pending, it can be
reset as follows:
Completely close the bonnet (locking in
place).
Turn the programme selector switch to
"ON".
Sit on the driver seat.
DANGER
Risk of personal injury or damage!
Observe the weight of the appliance
when you load it!
Do not use a forklift truck to unload the
machine as this may damage it.
ATTENTION
Charge the battery before commissioning
the machine.
When loading the appliance a suitable
ramp must be used!
If the machine is delivered on a pallet,
you must create an unloading ramp us-
ing the boards provided.
To unload the machine, proceed as follows:
Cut plastic packing belt and remove foil.
Remove the elastic tape fasteners at
the stop points.
Connect battery (see section on Care
and maintenance)
Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.
Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.
Slide the four support beams included
in the packaging under the ramp.
Remove the wooden blocks for locking
the wheels.
DANGER
Risk of accident, risk of injury!
It is prohibited to release the emergen-
cy brake on an incline without using the
stopper.
Before releasing the immobilizing
brake, the machine must be secured to
prevent it rolling away. If the device is
not secured, it will roll with a speed of
approx. 4.5 km/h after releasing the
parking brake until the electronics
brakes the device.
Release emergency brake:
Remove the brake level from the wheel
and put it in its position.
The immobilizing brake is thus deacti-
vated; the machine can now be moved.
Slide the machine over the prepared
ramp from the pallet.
Connect the battery, refer to Chapter
"Connecting and installing the battery".
Main switch to position 1/ON and insert
key (Intelligent Key).
Turn the programme selector switch to
position C (drive).
Press the drive direction switch and
slowly move the machine down from
the ramp.
Turn the programme selector switch to
position A (OFF).
Upon delivery the side brush is not in-
stalled, install side brush prior to commis-
sioning.
Refer to Chapter "Care and mainte-
nance/replacing the side brush".
Waste container (low emptying system)
Waste container (high emptying system)
Button for two-hand operation
Safety support waste container (high
emptying system)
Parking brake
Before Startup
Remove the appliance cover
Opening/closing cover on the left
Unloading tips
Net weight (transport weight)
Weight (without driver, without at-
tachment kits, without batteries)
KM 105/100 R (low emptying sys-
tem)
KM 105/110 R (high emptying
system)
305 kg
405 kg
Weight (without driver, without at-
tachment kits, with batteries)
KM 105/100 R (low emptying sys-
tem)
KM 105/110 R (high emptying
system)
490 kg
590 kg
* If upgrade kits are installed, the weight is
respectively higher.
Push the sweeper off the pallet
(appliance without built-in battery)
Drive the sweeper off the pallet
(appliance with built-in battery)
Install side brush
10
EN
