– 7
When unpacking the product, make sure that no acces-
sories are missing and that none of the package con-
tents have been damaged. If you detect any transport
damages please contact your dealer.
Illustrations on fold-out page!
1
Filter cover, front
2
Pre-filter
3
Fine filter
4
Filter cover, rear
5
Air outlet
6
Operating field
7
Air quality display
8
Filter cover handle
9
Air quality sensor cover
10 Main Supply
11 On/off operation button
12 Manual mode operation button
13 Automatic mode operation button
14 Night mode operation button
15 Change filter indicator
ATTENTION
Always operate the device with pre-filters and fine filters
installed.
Plug the mains connection into the device
Insert the mains plug into a socket.
All operation buttons on the control panel and the
air quality display light up briefly and go out again.
Press the on/off operation button in order to switch
the device on.
Note
–
When the device is switched on, the integrated air
quality sensor automatically measures the air qual-
ity in the room.
–
Set the desired mode by pressing the appropriate
operation button on the control panel.
When automatic mode is activated, the device selects
the appropriate fan speed for the measured air quality.
Press the on/off operation button in order to switch
the device on.
Press the automatic mode operation button.
The corresponding button lights up.
Note
–
The integrated air quality sensor measures the air
quality and automatically selects the right speed
level to ensure the best possible air quality in the
room.
–
As soon the air is clean, the device switches to low
fan speed.
When manual mode is activated, you can manually set
the fan speed.
Press the on/off operation button in order to switch
the device on.
Press the manual mode operation button.
The corresponding button lights up.
Note
–
By pressing the button several times, the fan speed
can be set in three speeds.
When night mode is activated, the control panel lighting
goes out, but the device remains in operation.
The control panel lighting is re-activated by touching the
control panel.
Press the on/off operation button in order to switch
the device on.
Press the night mode operation button.
The corresponding button lights up.
If the filter change indicator lights up:
see care and service.
Note
–
The filter change indicator flashes at 2 Hz if the fil-
ter service life is less than 72 hours.
–
The filter change indicator lights up continuously
when the end of the filter service life is reache
,
The appliance continues to work.
–
In order to reset the filter change indicator following
a filter change, press it for 5 seconds in standby
mode.
–
The filter change indicator only flashes/lights up
when the filter service life is less than 72 hours.
–
When there's a nasty smell, please take out the filter,
clean the dust on the surface of filter by using a va-
cuum cleaner or a hair dryer, then exposure the filter
in sunshine about 3-5 hours, and put it back in unit, if
the nasty smell still exist, please replace the filter.
Press the on/off operation button in order to switch
the device on.
Air quality display is lit:
Blue: Very good air quality
Yellow: Mediocre air quality
Red: Poor air quality
Description of the Appliance
Commissioning and operation
Start up
Operating field
Automatic mode
Manual mode
Display
Fan speed
low
medium
high
Night mode
Change filter indicator
Air quality display
17
EN
I
II
III
Summary of Contents for KA 4
