![background image](http://html2.mh-extra.com/html/karcher/k-2-300/k-2-300_user-manual_4247021007.webp)
- 7
Mount loose parts delivered with appliance prior
to start-up.
Illustrations on Page 3
Illustration
Î
Insert the transport wheels and lock them.
Illustration
Î
Transport handle / attach the transport han-
dle.
Illustration
Î
Pull out the clamp for the high-pressure hose
from the hand spray gun (e.g. a Philips
screwdriver).
Illustration
Î
Connect high pressure hose to trigger gun.
Î
Push the clamp in until it locks. Check the se-
cure connection by pulling on the high-pres-
sure hose.
Optional
Illustration
Î
Pull the suction hose for detergent through
the cover of the detergent tank until the filter
contacts teh bottom of the tank.
Î
Close the detergent tank with the lid.
Î
Lock the detergent tank in place on the appli-
ance.
Illustration
Î
Hook the accessories net into the hooks
shown in the illustration.
According to the applicable regula-
tions, the appliance must never be
used on the drinking water supply with-
out a system separator. Use a suitable
system separator manufactured by KÄRCHER;
or, as an alternative, a system separator as per
EN 12729 Type BA. Water flowing through a sys-
tem separator is considered non-drinkable.
Caution
Always connect the system separator to the wa-
ter supply, never directly to the appliance!
Note:
Impurities in the water can damage the
high-pressure pump and accessories. For pro-
tection, the use of the KÄRCHER water filter (op-
tional accessory, order no. 4.730-059) is
recommended.
Observe regulations of water supplier.
For connection values, see type plate/technical
data.
Î
Use a fibre-reinforced water hose (not in-
cluded) with a standard coupling. (Minimum
diameter 1/2 inch (13 mm), minimum length
7.5 m).
Illustration
Î
Screw the supplied coupling element to the
water connection on the appliance.
Î
Push the water supply hose onto the cou-
pling unit, then connect it to the water supply.
Caution
Dry runs lasting longer than two minutes lead to
damages to the high pressure pump. If the appli-
ance does not build up pressure within two min-
utes, switch it off and proceed as instructed in
the Chapter "Troubleshooting".
Illustration
Î
Connect the high pressure hose to the high
pressure connection of the appliance.
Illustration
Î
Push the spray lance into the trigger gun and
fasten it by turning it through 90°.
Î
Completely open the water tap.
Î
Insert the mains plug into the socket.
Î
Turn on the appliance “I/ON”.
몇
Danger
The trigger gun is subjected to a recoil force
when the water jet is discharged. Make sure that
you have a firm footing and are also holding the
trigger gun and spray lance firmly.
Illustration
Î
Unlock the lever on the trigger gun.
Î
Pull on the lever of the trigger gun; the device
will switch on.
Note:
Release the lever of the trigger gun; the
device will switch off again. High pressure re-
mains in the system.
For normal cleaning tasks.
Not suitable for use with detergents.
For particularly dirty items or areas.
Not suitable for use with detergents.
Carrying out the most common cleaning tasks.
The work pressure can be stagelessly regulated
between "Min" and "Max". You can add deter-
gent when "Mix" is selected.
Î
Release the lever on the trigger gun.
Illustration
Î
Turn the spray pipe to the desired position.
Before Startup
Water supply
Water supply from mains
Start up
Operation
Spray lance with high pressure nozzle
Spray lance with Dirtblaster
Spray pipe with pressure regulation (Vario
Power)
14
EN