background image

     

9

Release emergency-stop button by 
turning.

Release the trigger of the jet pistol. 

During breaks in operation, you can 
insert the jet pistol on the holder on 
the machine. 

NOTICE

During longer service interruptions, the 
dry ice pellets can agglutinate in the 
dry ice container. As far as possible, do 
not interrupt operations for more than 
20 minutes. In case of extended inter-
ruptions, empty the dry ice container.

A water separator cleans the com-
pressed air flowing to the device. This 
collects condensate in the water sepa-
rator, that needs to be drained once in 
a while.

Place the collection trough under 
the condensate drain screw.

Open the pressure relief valve 
slowly and wait until the conden-
sate has been drained from the de-
vice.

NOTICE

Please dispose of condensate in an 
environmentally friendly manner.

Set the appliance switch to "I".

Press the Statistics key briefly to 
display the operating duration.
t: Operation duration since the last 
reset.
T: Total operating duration.

Press the Statistics key briefly to 
display the processed dry ice 
amount.
m: Dry ice volume since the last re-
set.
M: Total dry ice volume.

Press the Statistics key briefly to 
display the average dry ice con-
sumption.
q: Average dry ice consumption 
since the last reset.
Q: Average total dry ice consump-
tion.

Turn the keyswitch in a clockwise 
direction.

Press the statistics key for 4 sec-
onds.

NOTICE

The total values cannot be erased.

Press the keys to increase and de-
crease the jet pressure at the same 
time and hold them, turn the key-
switch clockwise.

In the operating mode basic settings, 
the keys have the following functions:

1 Increase value
2 Decrease value
3 Menu point to the top
4 Menu point to the bottom

Turn the keyswitch counter-clock-
wise.

DANGER

Risk of cold burns. Dry ice has a tem-
perature of -79 °C. Never touch dry ice 
or cold parts of the machine without 
appropriate protection. Wear protec-
tive gloves and protective overalls.

DANGER

Risk of injury on account of flying dry 
ice pellets. Do not direct the jet pistol 
on persons. Keep third persons away 
from the place of use and when the 

machine is being operated (by cordon-
ing off the area).

Close the compressed air supply.

Place the collection trough under 
the condensate drain screw.

Open the pressure relief valve 
slowly and wait until the conden-
sate and the compressed air have 
been drained from the device.

Place the collection trough under 
the dry ice exit.

Press the key to empty the dry ice 
and wait until the dry ice container 
is empty.
The dry ice emptying stops after the 
preset time has elapsed (see "Basic 
Settings").
If needed, press the key to empty 
the dry ice container several times.

NOTICE

Please dispose of condensate in an 
environmentally friendly manner.

Set the appliance switch to "0/
OFF“.

Disconnect the machine from the 
compressed air inlet. 

Disconnect the main plug from the 
socket.

Clean and roll up the grounding 
rope.

Dispose of blasting debris accord-
ing to applicable regulations.

DANGER

Risk of accident on account of dry ice 
residue in the device. Remove all trac-
es of dry ice before transporting the de-
vice in closed vehicle; otherwise there 
is a risk of carbon dioxide suffocation 
to the co-passengers.

Carry out all the steps listed in the 
chapter "Shut down" before trans-
porting the device. 

Mount the appliance on the trans-
port vehicle. 

Lock the breaks of the steering roll-
ers. 

Fasten the device to the vehicle us-
ing fastening belts. 

CAUTION

Risk of injury and damage! Note the 
weight of the appliance in case of stor-
age.

This appliance must only be stored in 
interior rooms.

Switching on after emergency-

stop

Interrupting operation

Drain off the condensate.

Statistics functions

Retrieving values

Reset values

Basic settings

Menue point

Setting 
range

Description

Soft start

0, 1, 2, 3, 
4, 5 sec-
onds

Soft start, duration until 
the selected jet pres-
sure is reached

T_Dump

1, 2, 3, 4, 
5 minutes

Duration of the dry ice 
emptying process

Language

metric, 
imperial

Measurement units
metric: kg/h, MPa
imperial: lbs, psi

Lighting

ON/OFF Switch the nozzle light-

ing (option) on/off

Demo mode

ON/OFF Demo mode: The op-

eration is simulated, 
compressed air and 
dry ice dispensing is 
locked.

Finish the basic settings

Shutting down

TRANSPORT

Storing the device

11

EN

Summary of Contents for IB 15/120













































Reviews: