English
17
Frost protection
ATTENTION
Frost destroys the device if it is not completely
drained of water.
Store the device in a frost-free location.
If frost-free storage is not possible:
1. Drain excess water.
2. Pump commonly available anti-freeze through the
device.
3. Allow the device to run for a maximum of 1 minute
until the pump and lines are empty.
Note
Use commonly available, Glycol-based vehicle anti-
freeze. Observe the handling instructions of the anti-
freeze manufacturer.
Care and service
ATTENTION
Danger due to device inadvertently starting up
Risk of injury
Switch off the engine switch and remove the spark plug
connector prior to all work on the device.
몇
CAUTION
Hot surfaces
Risk of injury
Allow the device to cool down prior to all work.
Note
Observe the information on care and service in the orig-
inal instructions for the motor.
Safety inspection/maintenance contract
You can agree on regular safety inspections or close a
maintenance contract with your dealer. Please seek ad-
vice on this.
Maintenance intervals
Each time before use
Check the high-pressure hose for damage.
Immediately replace a damaged high-pressure
hose.
Check the device for leaks.
3 drops of water per minute are permissible. Contact
Customer Service in the case of more serious leaks.
Weekly
1. Check the oil level of the engine and pump. Contact
Customer Service if the oil is milky (water mixing
with the oil).
2. Clean the water filter, see Chapter
.
After the first 50 operating hours
Replace the oil in the high-pressure pump.
After 100 operating hours
1 Replace the oil in the engine.
2 Carry out maintenance tasks on the engine accord-
ing to the specifications provided in the operating in-
structions of the engine.
Every 500 operating hours, at least once annually
Have the device maintained by Customer Service.
Maintenance work
Cleaning the water filter
1. Shut off the water inlet.
2. Unscrew the filter cup.
Illustration D
1
Water filter
2
Filter insert
3
Filter chamber
3. Pull the filter insert downwards and off.
4. Clean the filter insert and filter cup.
5. Re-install the filter insert.
6. Screw on the filter cup again and tighten.
Replacing the oil in the high-pressure pump
For the oil type and filling quantity, see Chapter
.
1. Provide a catch pan for at least 1 litre of oil.
2. Unscrew the oil drain plug.
3. Drain the oil into the catch pan.
4. Screw in the oil drain plug.
5. Slowly fill with new oil until the middle of the oil level
indicator is reached. Air bubbles must be able to es-
cape.
Troubleshooting guide
DANGER
Risk of injury if the device is left running in an unattended state.
Switch off the engine and remove the spark plug connector before performing any work on the device.
Risk of burns!
Do not touch hot mufflers, cylinders or radiator ribs.
In case of any malfunctions not mentioned in this chapter, contact the authorised Customer Service when in doubt or
when you have been explicitly advised to do so.
Fault
Remedy
Device does not start
Follow operating instructions of the motor manufacturer!
Contact Customer Service if necessary.
Device does not reach
required pressure
Check operating speed of the motor.
Check the size of the nozzle and compare with the required size specified in the chap-
ter
.
Vent the device, see Chapter
.
Clean the water filter.
Check the water supply volume and compare with the required volume specified in
the chapter
.
Clean all inlet pipes to the pump.
Contact Customer Service if necessary.
Summary of Contents for HD 6/15 G Classic
