– 2
High-pressure jets can be dan-
gerous if improperly used. The
jet may not be directed at per-
sons, animals, live electrical equipment or
at the appliance itself.
Use this high pressure cleaner exclusively
for
–
Cleaning using low pressure jet and de-
tergent (for e.g. for cleaning machines,
cars, buildings, tools),
–
For cleaning using high pressure jet
without detergent (for e.g. for cleaning
facades, terraces, garden appliances).
For stubborn dirt, we recommend the use of
the dirt blaster as a special accessory.
Safety devices serve for the protection of
the user and must not be put out of opera-
tion or bypassed with respect to their func-
tion.
–
While reducing the water supply/quanti-
ty regulation at the pump head, the
overflow valve opens and part of the
water flows back to the pump suck side.
–
If the lever on the trigger gun is released
the pressure switch turns off the pump,
the high-pressure jet is stopped. If the
lever is pulled the pump is turned on
again.
The overflow valve and pressure switch are
set and sealed at the factory. Setting only
by customer service.
–
Check the contents of the pack before
unpacking.
–
In case of transport damage inform ven-
dor immediately
–
Store the drilling template on the carton
to assemble the device.
Caution
Risk of injury and damage! Note the weight
of the appliance during installation.
The enclosed fastener is not suitable for
fastening to concrete walls.
Risk of damage! Freezing water in the ap-
pliance can destroy parts of the appliance.
The machine should be stored in frost-free
rooms. In case there is frosting risk, for e.g.
if the machine is installed in open areas,
then the machine must first be emptied and
flushed using an anti-freezing agent.v
Î
Check the wall's support capacity.
Î
Drill 2 holes of 10 mm diameter into the
wall using the drilling template on the
packaging.
Î
Insert the enclosed heavy load dowel
into the holes.
Î
Remove side panels.
Î
Hang up the appliance and secure it
against falling down.
Î
Tighten the nuts of the heavy load dowel.
Î
Replace side panels.
Î
Loosen the fastening screws, remove
the hood.
Î
Cut off tip of oil container cover
Î
Check oil level in the oil tank.
Î
Fasten the hood.
Î
Mount the nozzle on the spray pipe (mark-
ings on the adjustment ring at the top).
Î
Connect ray tube to hand spray gun
Î
Lever out the safety clip of the handspray
gun using a screw-driver (Picture A).
Î
Place the hand-spray gun upside down
and insert the end of the high pressure
hose till the end. Ensure that the lose
disc falls right below on the hose end
(Picture B).
Î
Press the safety clip back into the hand-
spray gun. The hose can be pulled out
max. 1 mm if it has been installed cor-
rectly. Otherwise, it means the disc has
been installed wrongly (picture C).
Symbols on the machine
Proper use
Safety Devices
Overflow valve with pressure switch
Before Startup
Unpacking
Fasten the device to the wall
Check oil level
Attaching the Accessories
14
EN
Summary of Contents for HD 6/13 ST
