![background image](http://html1.mh-extra.com/html/karcher/b-110-d-65/b-110-d-65_manual_655156016.webp)
16
English
3
Spirit level
5. Unscrew the nut.
6. Adjust the screw so that the spirit level indicator is be-
tween the two lines.
7. Tighten the nut.
8. To check the new setting, move the device forward
again a short distance. Repeat the adjustment process
if necessary.
9. Turn the program switch to "OFF".
Adjusting the height
The height adjustment affects the bending of the suction
lips on contact with the floor.
Note
Standard setting:
3 washers above, 3 washers below the
suction bar.
Uneven floor:
5 washers above, 1 washer below the suc-
tion bar.
Very smooth floor:
1 washer above, 5 washers below the
suction bar.
1. Unscrew the nuts.
1
Nut
2
Washer
´
3
Spacer roller with holder
2. Place the desired number of washers between the suc-
tion bar and the spacer roller.
3. Fit the remaining washers above the spacer roller.
4. Screw on the nut and tighten.
5. Repeat the entire procedure at the other spacer roller.
Note
Set both spacer rollers to the same height.
Adjusting the squeegee blades
The squeegee blades only need to be adjusted on the D
cleaning head.
1. Adjust the squeegee blades by turning the adjustment
wheel so that the squeegee blade touches the ground.
2. Turn the adjustment wheel an additional 1 turn down-
wards.
Cleaning
1. Sit on the seat.
2. Insert the Intelligent Key.
3. Set the safety button to "1".
4. Set the travel direction switch to forward travel.
5. Set the program switch to the desired cleaning program.
6. Determine the speed with the accelerator pedal.
7. Determine the travel direction with the steering wheel.
8. Drive over the surface to be cleaned.
Side scrubbing deck (option)
The side scrubbing deck makes working close to the edge
easier.
Note
The side scrubbing deck is not active in the polish and vac-
uum cleaning programs.
1. Operate the side scrubbing deck switch.
The side scrubbing deck is activated.
2. To finish working with the side scrubbing deck, set the
side scrubbing deck switch to "0" .
Finishing operation
Finishing cleaning
1. Set the program switch to Drive.
2. Continue moving a short distance.
The residual water is vacuumed up.
3. Turn the program switch to "OFF".
4. Remove the Intelligent Key.
5. Charge the batteries if necessary.
Draining the waste water
몇
WARNING
Improper disposal of waste water
Environmental pollution
Observe the local waste water treatment regulations.
Note
When the waste water tank is full, the suction volume is in-
terrupted by a float to prevent the waste water tank from
overflowing. In this case, drain the waste water.
1. Remove the waste water drain hose from the holder and
open the cover of the drain hose.
2. Squeeze the end of the hose and lower it over the dis-
posal facility.
3. Adjust the strength of the waste water jet by squeezing
the end of the hose.
4. Rinse the waste water tank with clear water.
5. Close the drain hose cover.
6. Press the waste water hose into the holder on the de-
vice.
Waste water tank rinsing system (option)
1. Remove the waste water drain hose from the holder and
open the cover of the drain hose.
2. Close the cover of the waste water tank.
3. Connect a water supply hose to the water connection of
the waste water tank rinsing system.
4. Open the water inlet and rinse the waste water tank for
about 30 seconds.
5. Repeat the rinsing process 2 to 3 times if necessary.