English
15
9. Set the program switch to "OFF", wait briefly and then
set to the desired program.
Filling with fresh water
Filling with fresh water via the filling system
1. Connect the water hose to the connection nozzle of the
filling system (maximum water temperature 50 °C).
2. Open the water inlet.
3. Monitor the device, the automatic filling system inter-
rupts the water supply when the fresh water tank is full.
4. Close the water inlet.
5. Remove the water hose.
Filling with fresh water
1. Open the fresh water tank lock.
2. Fill fresh water (max. 50 °C) to the lower edge of the fill-
ing nozzle.
Note:
The fresh water hose can be clamped in the hose
switch during filling.
3. Close the fresh water tank lock.
Filling with detergent
Notes on detergents
몇
WARNING
Unsuitable detergents
Health risk, damage to the device
Use only recommended detergents. The operator carries
all increased risks relating to operational safety and in-
creased risk of accidents if using other detergents.
Use only detergents free of chlorine, solvents, salt and hy-
drofluoric acid.
Adhere to the safety instructions stated on the detergent
packaging.
Note
Do not use heavily foaming detergent.
Recommended detergents
Filling detergent via the dosing device
Only with DOSE variant:
Detergent is added to the fresh water on the way to the
cleaning head by a dosing device.
1. Unlock the waste water tank and pivot it to the rear.
2. Fill the detergent canister with detergent.
3. Pivot the waste water tank forwards.
Note
A maximum of 5% detergent can be added using the dos-
ing device. For a higher dosage, the detergent must be
added to the fresh water tank.
Filling the detergent into the fresh water tank
1. Fill the detergent into the fresh water tank.
Note:
The cap of the fresh water tank filling hole can be
used for measuring the detergent. It is fitted with a scale
on the inside.
Adjusting parameters
1. Set the program switch to the desired cleaning program.
2. Turn the Info button until the desired parameter is dis-
played.
3. Press the Info button.
The adjusted value flashes.
4. Set the desired value by turning the Info button.
5. Confirm the changed setting by pressing the Info button
or wait until the set value is automatically accepted after
10 seconds.
Yellow Intelligent Key
The yellow Intelligent Key authorizes functions that are re-
quired for the cleaning task.
The parameters for the various cleaning programs are pre-
set in the device. Individual parameters can be changed
depending on the authorization of the yellow Intelligent
Key.
The display texts for parameter settings are largely self-ex-
planatory.
"FACT" parameters (only available with R cleaning head):
●
"Fine Clean": Low brush speed for removing gray film
from fine stone.
●
"Whisper Clean": Medium brush speed for maintenance
cleaning with reduced noise level.
●
"Power Clean": High brush speed for polishing, crystal-
lizing and sweeping.
Adjusting the suction bar
Adjusting the inclination
The inclination must be adjusted so that the suction lips of
the suction bar make even contact with the floor over the
entire length of the suction bar.
1. Park the device on a surface without a slope.
2. Turn the program switch to the "Vacuum" position.
3. Drive the device a small distance forwards.
4. Read the spirit level.
1
Screw
2
Nut
Usage
Detergent
Maintenance cleaning of all water-re-
sistant floors
RM 746
RM 756
RM 780
Maintenance cleaning of polished
hard surfaces (e.g. granite)
RM 755 es
Maintenance cleaning, intermediate
cleaning and basic cleaning of indus-
trial floors
RM 69 ASF
Maintenance cleaning and basic
cleaning of fine stone tiles
RM 753
Maintenance cleaning of tiles in sani-
tary areas
RM 751
Coating removal on all alkaline-resis-
tant floors (e.g. PVC)
RM 752
Coating removal on linoleum floors
RM 754