background image

1

NEVER!

Model 2700 DH/DB, 3000 DH & 3500 DH/DB OVERVIEW      

Item Description

1. High pressure outlet
2. Water inlet with garden hose

connector and filter

3. Detergent suction tube
4. Knob Assembly (two each, Bolt

& Knob)

5. High pressure hose
6. Detergent filter
7. Handle
8. Trigger gun 
9. Trigger gun safety lock

10. Pull start (not pictured)
11. Gas tank
12. Oil fill cap (not pictured)
13. Spray wand
14. Dirtblaster

®

nozzle

15. Pressure control
16. Gun/hose storage handle
17. Nozzle
18. Detergent tray
19. Operator manuals

Features:
•  Low oil sensor
• Thermal 

protection sensor

2

15

4

3

7

14

5

6

9

Never

point nozzle at people or animals.

Never

drink alcohol or use drugs while operating this equipment.

Never

spray electrical connections, electrical outlets or fixtures.

Never

add fuel with the engine running or operate where fuel has been spilled.

Never

touch hot surfaces or allow accessories to contact hot surfaces.

Never

operate in an enclosed space, exhaust fumes are dangerous.

Never

operate near utilities with open flames.

Never

operate pressure washer without the water turned on.

Never

use hot water.

1

11

13

17

19

16

8

18

NOTE: Engines controls shown may appear different.

Summary of Contents for 1.187-115













Reviews: