background image

11

TROUBLESHOOTING 

– continued

Symptom Cause 

Solution

No detergent.

Garden hose 
connection leaks.

Pump is noisy.

Water leaks
from pump.

Oil Drip.

Detergent is too thick.

Dilute detergent. For best results, 
use Kärcher detergent.

Filter on detergent suc-
tion tube is clogged.

Run warm water through filter to
remove debris.

Detergent filter valve is
at lowest setting.

Set detergent filter valve to a high-
er setting.

Damaged or clogged
detergent suction tube.

Remove obstruction or 
replace detergent suction tube.

A high pressure
nozzle is attached.

Replace with black
detergent nozzle.

Discharge nozzle 
is obstructed.

Blow out or remove debris 
with fine needle.

Loose fittings.

Tighten fittings.

Missing/worn rubber washer.

Insert new washer.

Spray wand not properly
attached.

Broken o-ring.

Check that hoses and fittings are
air tight. Turn off machine and
purge pump by squeezing trigger
gun until a steady flow of water
emerges through the nozzle.

Loose fittings.

Check that all fittings are tight.

Call service center.

Water seals are 
damaged or worn.

Thermal protection
device will auto reset.

Thermal protection
device is activated.

Call Kärcher customer service 
hotline and order an o-ring.

Pump is sucking air.

Oil seals are damaged 
or worn.

Call service center.

Spray wand leaks.

Slide the spray wand into the gun.
Turn the wand collar clockwise
onto the gun threads until tight.

Detergent suction tube 
not properly connected 
to the machine.

Check connection.

If you encounter any additional 
difficulties not listed, please call 
our service center for help.

Kärcher Customer Support USA

In USA Call:

1-800-537-4129

or visit our website: www.karcher-usa.com

Summary of Contents for 1.187-115













Reviews: