Karcher Shark HDS 2.0/10 Ed Cage Operator'S Manual Download Page 8

9.800-191.0  •  Rev. 10/09

OPERATOR’S MANUAL

  

 

PRESSURE WASHER 

 

8

OPERATINg INSTRUCTIONS

HOW TO USE THE  

DETERgENT INjECTOR

WARNING:  Some  detergents 
may be harmful if inhaled or in-
gested causing severe nausea, 
fainting or poisoning. The harm-
ful elements may cause property 
damage or severe injury.

The machine can siphon and mix 
detergents with the use of Shark's 
detergent injector kit.

  1.  Pull injector quick coupler collar back and secure on 

discharge nipple. Injector valve body arrow should 
point in direction of flow.

  2.  Connect high pressure hose to injector nipple se-

curing quick coupler.

  3.  Start  machine  as  outlined  in  Operating  Instruc-

tions.

  4.  Place  detergent  pick-up  tube  into  container  of 

detergent solution.

  5.  Turn pressure control handle counterclockwise on 

the variable pressure wand. This lowers the pres-
sure by directing the water flow through the soap 
nozzle and allows the detergent injector to siphon 
soap. 

   6.  Open trigger spray gun. Water detergent ratio is  

approximately 15 to 1.

   7.  When you finish washing, rinse by simply turning 

the variable pressure wand control handle clock-
wise to increase pressure.

 

  NOTE: The detergent injector will not siphon with 

water flowing through the high pressure nozzle at 
the end of the wand.

   8.  For  clean  up,  place  detergent  pick-up  tube  into 

container of clear water and follow steps 5 and 8 
to prevent detergent deposits from damaging the 
injector.

WARNING

SOME DETERgENTS 

MAy bE HARMfUL 

If INHALED OR 

INgESTED.

HOT 

WATE

R OU

TLET

SALI

DA D

EL AG

UA C

ALIE

NTE

SORT

IE D'E

AU C

HAUD

E

CH

AU

D!

Adjustable 

Thermostat

Discharge Nipple

Detergent Injector

Collar

variable Pressure 

Control Handle

quick Coupler

Trigger

Rupture Disk

brass Soap 

Nozzle

variable Pressure 

Wand (vP)

High Pressure 

Hose

Spray gun

Nozzle quick 

Coupler

Detergent 

Pickup Tube

Summary of Contents for HDS 2.0/10 Ed Cage





























Reviews: