Kanmor 360e Data Brochure Download Page 1

Page: 1 / 20

- Data Brochure

Mixing Control 360e

D 360e

06/03

1 of 20

D 360e - 06/03

The Mixing Control 360e is designed to control the supply water temperature to a hydronic system in order to provide outdoor
reset or setpoint operation. The control uses a floating action mixing valve to regulate the supply water temperature, while
protecting the boiler against flue gas condensation. The control has a Liquid Crystal Display (LCD) to view system status and
operating information.

Additional Functions Include:

• Quick Setup for easy installation and programming of

control

• User comfort adjustment to increase or decrease build-

ing space temperature

• Advanced settings to fine-tune building requirements

• Boiler Control for improved energy savings

• Powered mixing system pump output

• Optional indoor sensor for room air temperature control

• Test sequence to ensure proper component operation

• Setback input for energy savings

• 230 V (ac) power supply

• CE Approved

Input

Mixing

Demand

Signal

Output

Mixing System

Pump

Input

Indoor
Sensor

Optional

Input

Universal Sensor

Included

Input

Universal Sensor

Included

Input

Outdoor
Sensor

Included

Output

Boiler

Input

230 V (ac)

Power

Supply

Input

kanmor Timer

Optional

Output

Mixing Valve &

Actuating Motor

Do not apply power

Signal wiring must be

rated at least 300 V.

Pmp

Sys

UnO Com Boil

Mix

Pwr Opn Cls

Mix Com Out Indr

9 10

7 8

12 13 14 15 16 17 18

Mix

Power

Boiler

Demand

Advanced

Installer

Boiler Sensor

Supply

30% Enable

10% Enable

Return

Item

Test

Terminal

Unit

Mixing

Demand

INSTALLATION CATEGORY II

Made in Canada

Power:

230 V

10% 50 Hz 2300 VA

Relays:

230 V (ac) 10 A 1/3 hp, pilot duty 240 VA

Demand:

20 to 260 V (ac) 2 VA

To increase or decrease the
building temperature:

• Press the

Item

▲

▼

buttons

simultaneously for 1 sec. to
enter the ADJUST menu
• Use the

▲

▼

buttons to adjust

the

ROOM

setting

Display defaults back to VIEW
menu after 20 seconds.

ROOM

Set to desired room temperature.

OUTDR DSGN

Set to coldest (design)

outdoor temperature.
Terminal Unit

Set to

High Mass Radiant

Low Mass Radiant

Fan Coil

Convector 4

Radiator 5

Baseboard 6

Refer to brochure for more information.

Installer Instructions

Mixing Control 360e

Floating Action

Open

Motor

Speed

Summary of Contents for 360e





















Search results

Summary of Contents for 360e

Reviews:

Related manuals for 360e

Brands by name

Popular brands

Kanmor 360e, Data Brochure

Search results

Summary of Contents for 360e

Reviews:

Related manuals for 360e

Brands by name

Popular brands