17
WOODEN SURFACES
Wash with a soft cloth and hot soapy water solution. Rinse with water. Do not use abrasive cleaners,
degreasers or a concentrated barbecue cleaner on wooden parts.
COOKING GRID
Use a mild soapy water solution. Non-abrasive scouring power can be used on stubborn stains then rinse
with water.
CLEANING THE BURNER ASSEMBLY
Turn the gas OFF at the control knob
and disconnect the cylinder.
Remove cooling grate.
Clean the burner with a soft brush or
blow clean with compressed air and
wipe with a cloth.
Clean any clogged ports with a pipe
cleaner or stiff wire (such as an
opened paper clip).
Inspect burner for any damage (cracks or holes). If damage is found, replace with a new burner.
Reinstall the burner, check to ensure that the Gas valve orifices are correctly positioned and secured
inside the burner inlet (venturi).
SERVICING
Your gas barbecue should be serviced annually by a competent registered person.
TROUBLE SHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
Burners will not light using
the ignition system
1. LP gas cylinder is empty
2. faulty regulator
3. obstructions in burner
4. obstructions in gas jets or gas hose
5. electrode wire loose or disconnected on
electrode or ignition unit
6. electrode or wire is damaged faulty
pushbutton igniter
1. replace with full cylinder
2. have regulator checked or replace
3. clean burner
4. clean jets and gas hose
5. reconnect wire
6. change electrode and wire
change igniter
Burner will not light with a
match
1. LG gas cylinder is empty
2. Faulty regulator
3. bstructions in burner
4. Obstructions in gas jets or gas hose
1. Replace with full cylinder
2. Have regulator checked or replace
3. Clean burner
4. Clean jets and gas hose
Low flame or flashback (fire
in burner tube-a hissing or
roaring noise may be heard)
1. LP gas cylinder too small
2. Obstructions in burner
3. Obstructions in gas jets or gas hose
4. Windy conditions
1. Use larger cylinder
2. Clean burner
3. Clean jets and gas hose
4. Use BBQ in a more sheltered position
THIS SIDE UP
PLEASE NOTE THE BURNER DIRECTION
Summary of Contents for KYQ-HK3N
