background image

SECTION 3 / OIL LEAKS

13

Problems That Cause Oil Leaks

A. Drain Plug

A loose drain plug (6) or damaged drain plug ring (5).

B. Oil Reservoir

A damaged oil reservoir (3), missing oil reservoir filter (2), or damaged O-ring (4).
If the oil bath housing (7) is overfilled, oil will leak from vent cap (1).

C. Weep holes

If oil is leaking from the weep holes (15), there is either a leak in the low-pressure
seals (39) or the high-pressure seals (20); or there is piston (13) damage.

D. Pump Shaft Seal

A damaged or worn pump shaft seal (8).

12...Swash 

10...Swash assembly

9...Forward O ring

8...Pump shaft seal

7...Oil bath housing

4...O-ring

3...Oil reservoir

2...Oil filter

1...Oil reservoir vent cap

31...Detergent check valve

32...O-ring

33...Ball bearing

34...Spring

17...Pressure/volume control knob

18...Bypass valve

19...Bushing

30...Water inlet filter

25...Low pressure check valve basket (3)

56...Water outlet bolt (4)

13...Piston (3)

46...High pressure valve seat (3)

38...Thermal relief valve

20...High pressure seal (3)

6...Oil drain 

plug

39...Low pressure oil seal (3)

40...Seal retaining ring (3)

41...Bushing seal (3)

42...Bushing (3)

45...High pressure valve slide

55...Safety relief valve

54...Ball bearing

53...Ball bearing seat

52...Spring

51...Pump head bolt (4)

50...High pressure valve cap (3)

37...Retainer nut

47...High pressure valve plate (3)

48...High pressure valve spring (3)

49...High pressure valve basket (3)

26...Low pressure check valve spring (3)

27...Low pressure check valve plate (3)

28...Low pressure check valve seat (3)

44...Piston guide retaining screw (2)

22...Water outlet

43...Scraper ring (3)

35...Detergent tube

36...Detergent filter

5...Oil drain 

plug ring

11...Swash plate ball bearings

29...Water inlet

23...Non-return check valve

24...Nozzle insert

21...Pump head

14...Piston spring (3)

16...Piston housing

15...Weep holes (3)

Pump 785  9/28/01  3:06 PM  Page 13

www.mymowerparts.com

For Karcher Pressure Washer Parts Call 606-678-9623 or 606-561-4983

Summary of Contents for 3.532-757.0


















Reviews: