EN
6
4445103584
Setting up the shelter
I
Keep the following tips in mind while setting up the shelter:
•
The figures provide a general overview of the set-up. The actual set-up
will vary slightly based on the model of shelter.
•
Get help. The set-up is easier with more people.
•
Push the poles into the sleeves from front to rear.
•
After standing the shelter upright, check the corner pegs and re-peg
if necessary. The groundsheet on the inside should be taut and in a
rectangular shape.
•
Peg the guy lines so that the shelter is under tension without distorting
the shape.
•
If available, attach the storm straps.
•
Check the guy lines from time to time to ensure adequate tension, if
necessary use the runners to adjust.
Set up the shelter as follows:
1. To protect the shelter from dirt and damage, lay down a groundsheet
or footprint before unpacking.
2. Unpack the shelter.
3. Separate and identify the different components.
4. Proceed as shown to set up the shelter (fig.
1
, page 3 to fig.
7
,
page 4).
Dismantling the shelter
A
1. Reverse the set up procedure.
2. Push the poles out of the sleeves, do not pull.
3. Ensure that all parts are clean before packing in the carry bag.
4. If the shelter is wet or damp, dry fully as soon as possible.
Cleaning and maintenance
A
1. If necessary, clean the product with clean water and a soft brush.
2. Apply impregnation against water and UV radiation before each trip.
Storing the shelter
I
1. Clean the shelter.
2. Air fully and ensure the shelter is totally dry before packing away.
3. Store in a well ventilated dry place.
Troubleshooting
I
Disposal
➤
Place the packaging material in the appropriate recycling waste bins,
wherever possible.
➤
Consult a local recycling center or specialist dealer for details about
how to dispose of the product in accordance with the applicable dis-
posal regulations.
Warranty
The statutory warranty period applies. If the product is defective, please
contact the manufacturer's branch in your country (see
kampaoutdoors.com/store-locator) or your retailer.
For repair and warranty processing, please include the following docu-
ments when you send in the device:
•
A copy of the receipt with purchase date
•
A reason for the claim or description of the fault
The warranty covers manufacturing defects, materials and parts. The
warranty does not cover fading of the cover and wear and tear due to
UV radiation, misuse, accidental damage, storm damage, or permanent,
semi-permanent or commercial use. It does not cover any resulting
damage. Please contact your dealer for claims. This does not affect your
statutory rights.
NOTE
•
The shelter comes with general purpose pegs. These
will be suitable for many sites but for some types of
ground special pegs will be needed. Ask your dealer.
•
Drive the pegs at a 45° angle away from the shelter into
the ground.
•
Peg each guy line in-line with the seam it starts from.
NOTICE! Material damage
Do not use force when dismantling the shelter. Otherwise
you might damage any material.
NOTICE! Damage hazard
•
Do not use sharp or hard objects or cleaning agents for
cleaning.
•
Do not use alcohol based materials, chemicals, soap
and detergents for cleaning.
•
Remove bird droppings and tree resin as soon as
possible to avoid permanent damage to the material.
NOTE
•
Fully set up the shelter for cleaning.
•
Choose a sunny day for cleaning to ensure the material
will dry thoroughly.
NOTE
•
During first exposure to water there may be some
moisture at the seams. Through this moisture the threads
will swell and fill the holes that are created in the sewing
process.
•
A fully equipped spare parts kit should include:
–
Waterproofer
–
Repair tape and repair solution
–
Silicone spray for the zippers
–
Spare pegs
Problem
Solution
Water leak
➤
Check for leaky seams, damaged
tapings and moist areas.
➤
If you find any leaks, apply seam
sealant.
Rip in the fabric
➤
Use repair tape to seal the fabric.
➤
Have repairs carried out by an
authorized specialist.
Shock cord connecting the poles
has broken
➤
Purchase replacement shock cord.
➤
Replace the shock cord.
Pole has broken
➤
Use a metal peg as a splint by taping it
to the broken pole.
➤
Purchase a new pole.
KampaPoledShelter300_IOM_4445103584_EMEA16_20xx-xx-xx.book Seite 6 Mittwoch, 1. Dezember 2021 9:01 21
