background image

PROTECTION AND LOCATION OF YOUR SET 

11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or

laundry tub, in a wet basement, or near a swimming pool, etc. 

Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set 

from the wall outlet and refer servicing to qualified service personnel. 

12. Choose a place where light (artificial or sunlight) does not shine directly on the screen.

13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists.

14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the

receiver, to protect it from overheating. These openings must not be blocked or covered.

Never cover the slots or openings with cloth or other material. 
Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc. 
Never place the set near or over a radiator or heat register. 
Never place the set in a

 

built-in enclosure, unless proper ventilation is provided. 

PROTECTION AND LOCATION OF YOUR SET 

15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide 

some  protection  against  voltage  surges  and  built  up  static  charges,  Section  810  of  the  National  Electrical  Code, 
NFPA  No.  70-1975,  provides  information  with  respect  to  proper  grounding  of  the  mast  and  supporting  structure, 
grounding  of  the  lead-in  wire  to  an  antenna  discharge  unit,  size  of  grounding  conductors,  location  of  antenna 
discharge unit, connection to grounding electrode, and requirements for the grounding electrode. 

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTR UCTIONS 

EXAMPLE OF ANTENNA GROUNDING AS PER 

NATIONAL ELECTRICAL CODE 

ANTENNA 

 LEAD- IN WIRE 

GROUND CLAMP 

ANTENNA DISCHARGE 
UNIT (NEC SECTION 
810-20) 

GROUNDING 
CONDUCTORS 

ELECTRIC SERVICE

(NEC SECTION810-21) 

EQUIPMENT 

 GROUND CLAMPS 

POWER SERVICE GROUNDING 

NEC-NATIONAL ELECTRICAL CODE 

ELECTRODE SYSTEM

 (NEC ART 250. PART H) 

15.2. Note to CATV system installer : (Only for the television set with CATV reception) 

This reminder is provided to call the CATV system installer s attention to Ar ticle 820-40 of the NEC that 
provides  guidelines  for  proper  grounding  and,  in  particular,  specifies  that  the  cable  ground  shall  be 
connected to the grounding system of the building, as close to the point of cable entry as practical. 

16.

An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power
circuits,  or  where  it  can  fall  into  such  power  lines  or  circuits.  When  installing  an  outside  antenna  system,  extreme  care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. For  added  protection  for  this  television  set  during  a  lightning  storm,  or  when  it  is  left  unattended  and

unused  for  long  periods  of  time,  unplug  it  from  the  wall  outlet  and  disconnect  the  antenna.  This  will
prevent damage due to lightning and power-line surges.

Summary of Contents for K-LED32HDXDT2






































Reviews: