background image

7

If the gas fire is not installed correctly, 
all warranty and/or damage claims 
against Archifire Fireplaces will be 
declared null and void.

This gas fire has been tested and 
approved according to AS5263-1-3:2016 
standard. Every gas fire that leaves the 
factory has been tested for technical 
and functional adherence to relevant 
quality standards in force.

This user instruction is available in 
various languages on www.kalfire.com, 
or through your installation bureau. 
All translated instructions have been 
translated from a Dutch instruction,  
which is the original document. 

Disclaimer

All rights reserved. No part of this 
manual may be copied, distributed 
or translated into other languages, 
in full or in part, without the prior 
written permission of Kalfire. Kalfire 
reserves the right to make changes to 
the manual. Kalfire, however, cannot 
provide any warranty, implicitly or 
explicitly, for this manual. Any risk is 
fully for the account of the user. 

Copyright @ 2020 Kalfire B.V. 
 Geloërveldweg 21, Belfeld,  
The Netherlands

 

1. General information

The following sections provide general 
information about the gas fire:
-   Foreword 
-   Pictograms 
-   Warranty 

 
1.1  Foreword

About this manual

This user instruction has been written 
for the users of the gas fire. A seperate 
Installation Manual accompanies this 
User Instructions. The user instructions 
should remain in the vicinity of the gas 
fire so that they are readily available for 
fireplace users.

Maintenance and repair work may only 
be carried out by authorised technical 
fitters.

Effective use

This gas fire has been designed as 
ambiance heating and has not been 
designed to be used as the principal 
heating unit for part of a house or 
throughout the house.

The gas fire and accompanying remote 
control may only be used in accordance 
with the reason it was designed and 
after review of the Installation Manual 
and user instructions.

Modifications of whatever nature can 
also affect the safety of the gas fire. 
Alterations can nullify the warranty and 
the periodic inspection of the gas fire 
will come to lapse.

Summary of Contents for G160/41F





































Reviews: