background image

3

Top Control Dishwasher

Introduction

Congratulations on your purchase of a high-quality Insignia product. Your NS-DWH2BS8 / NS-DWH2SS8 /
NS-DWR2BS8 / NS-DWR2WH8 / NS-DWR2SS8 represents the state of the art in dishwasher design and is designed for 
reliable and trouble-free performance.
This installation guide will show you how to install your new dishwasher.

IMPORTANT SAFETY INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT

• Observe all governing codes and ordinances.

Note to Installer 

– Be sure to leave these instructions for the consumer’s and local inspector’s use.

Note to Consumer 

– Keep these instructions with your 

User Guide

 for future reference.

Skill Level 

– Installation of this dishwasher requires basic mechanical and electrical skills. 

Proper installation is the 

responsibility of the installer. Product failure due to improper installation is not covered under the appliance 
warranty.

Completion Time

 – One to three hours. New installations require more time than replacement installations.

IMPORTANT

• The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.
• If you received a damaged dishwasher, you should immediately call Insignia Customer Service at 1-877-467-4289.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While performing installations 
described in this booklet, gloves and safety glasses or goggles should be worn.

Warning

This dishwasher comes with a heating element to heat the water. To avoid the risk of a serious burn, don't touch the 
heating element when the dishwasher is on.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous voltage constituting a risk of 
electric shock is present within your refrigerator.

This symbol indicates that there are important operating and 
maintenance instructions in the literature accompanying your 
refrigerator.

WARNING: 

To reduce the risk of electrical shock, fire, or injury to persons, the installer must ensure that the dishwasher is 

completely enclosed at the time of installation.

Summary of Contents for KWM2414H























Reviews: