Other features
Operation Instructions
COOL operation
· Press the "MODE" button until the "COOL" indicator
light comes on.
· Press the ADJUST buttons "+" or "-" to select your
desired room temperature. The temperature can be
set within a range of 17°C~30°C/62°F~88°F(or 86°F).
· Press the "FAN SPEED" button to choose the
fanspeed.
DRY operation
· Press the "MODE" button until the "DRY" indicator
light comes on.
· The fan speed or the temperature cannot be
adjusted. The fan motor operates at LOW speed.
NOTE:Keep windows and doors closed for the best
dehumidifying effect. Do not put the duct to window.
FAN operation
· Press the "MODE" button until the"FAN " indicator
light comes on.
· Press the "FAN SPEED" button
on
the remote
controller to choose the fan speed. The temperature
can not be adjusted.
· Do not put the duct to window.
Operating
Instructions
AUTO operation(on some models)
· When you set the air conditioner in AUTO mode, it
will automatically select cooling, heating(cooling
only models without), or fan only operation
depending on what temperature you have selected
and the room temperature.
· The air conditioner will control room temperature
automatically round the temperature point set by
you.
· Under AUTO mode, you can not select the fan speed.
HEAT operation(cooling only models without)
· Press the "MODE" button until the "HEAT" indicator
light comes on.
· Press the ADJUST buttons "+" or " - " to select your
desired room temperature. The temperature can be
set within a range of 17°C~30°C/62°F~88°F (or 86°F).
· Press the "FAN SPEED" button on the remote
controller to choose the fan speed.
Wireless operation(on some models)
Used to initiate the wireless connection mode. For the
first time to use wireless function, press the mode
button for 3 seconds to initiate the wireless connection
mode when the unit is off . The LED DISPLAY shows 'AP'
to indicate you can set wireless connection. If
connection(router) is successful within 8 minutes, the
unit will exit wireless connection mode automatically
and the wireless indicator illuminates. If connection is
failure within 8 minutes, the unit exits wireless
connection mode automatically. After Wireless
connection is successful, for some models you can
press MODE and DOWN (-) buttons at the same time
for 3 seconds to turn off Wireless function and the LED
DISPLAY shows 'OF' for 3 seconds, press MODE button
and UP(+) to turn on Wireless function and the LED
DISPLAY shows 'ON' for 3 seconds.
NOTE: When you restart the wireless function, it may
take a period of time to connect to the network
automatically.
NOTE: Under AUTO mode, both the AUTO mode and
the actual operation mode indicator lights illuminate
for some models.
SLEEP/ECO operation
This feature can be activated from the remote control
ONLY. To activate SLEEP feature, the set temperature
will increase(cooling) or decrease(heating) by 1°C/2°F
(or 1°F) in 30 minutes. The set temperature will then
increase(cooling) or decrease(heating) by another 1°C
/2°F (or 1°F) after an additional 30 minutes. This new
temperature will be maintained for 7 hours before it
returns to the originally selected temperature. This
ends the Sleep mode and the unit will continue to
operate as originally programmed.
NOTE: This feature is unavailabe under FAN or DRY
mode.
FOLLOW ME/TEMP SENSING feature(on some models)
NOTE:This feature can be activated from the remote
control ONLY. The remote control serves as a remote
Operating
Instructions
thermostat allowing for the precise temperature
control at its location. To activate the Follow Me/Temp
Sensing feature, point the remote control towards the
unit and press the Follow Me/Temp Sensing button.
The remote control will send this signal to the air
conditioner until press the Follow Me/Temp Sensing
button again. If the unit does not receive the Follow
Me/Temp Sensing signal during any 7 minutes interval,
the unit will exit the Follow Me/Temp Sensing mode.
NOTE: This feature is unavailabe under FAN or DRY
mode.
AUTO-RESTART
If the unit breaks off unexpectedly due to the power
cut, it will restart with the previous function setting
automatically when the power resumes.
WAIT 3 MINUTES BEFORE RESUMING OPERATION
After the unit has stopped, it can not be restarted
operation in the first 3 minutes. This is to protect the
unit. Operation will automatically start after 3
minutes.
AIR FLOW DIRECTION ADJUSTMENT
Adjust the air flow direction manually:
· The louver can be set to the desired position manually.
· Do not place any heavy objects or other loads on the
louver, doing so will cause damage to the unit.
· Ensure the louver is fully opened under heating
operation.
· Keep the louver fully opened during operation.
WATER DRAINAGE
· During dehumidifying modes, remove the drain plug
from the back of the unit, install the drain connector
(5/8" universal female mender) with 3/4" hose(locally
purchased). For the models without drain connector,
just attach the drain hose to the hole. Place the open
end of the hose directly over the drain area in your
basement floor.
Remove the
drain plug
Continuous
drain hose
NOTE: Make sure the hose is secure so there are no
leaks. Direct the hose toward the drain, making sure
that there are no kinks that will stop the warter
flowing. Place the end of the hose into the drain and
make sure the end of the hose is down to let the water
flow smoothly. When the continuous drain hose is not
used, ensure that the drain plug and knob are installed
firmly to prevent leakage.
Continuous
drain hose
Remove the drain plug
· During heating pump mode, remove the lower drain
plug from the back of the unit, install the drain
connector(5/8" universal female mender) with 3/4"
hose(locally purchased). Carefully move the unit to a
drain location, and let the water drain away.
NOTE: Make sure the drain hose is lower than the
bottom tray drain outlet.
· When the water level of the bottom tray reaches a
predetermined level, the unit beeps 8 times, the
digital display area shows "P1" . At this time the air
conditioning/dehumidification process will
immediately stop. However, the fan motor will
continue to operate(this is normal). Carefully move
the unit to a drain location, remove the bottom drain
plug and let the water drain away. Reinstall the
bottom drain plug and restart the machine until the
"P1" symbol disappears. If the error repeats, call for
service.
NOTE: Be sure to reinstall the bottom drain plug firmly
to revent leakage before using the unit.
Bottom drain
plug
POWER MANAGEMENT feature(On some models)
Under cooling operation, when the ambient
temperature is lower than the setting temperature for
a period of time, the unit will be automatically operate
power management feature. The compressor and fan
motor stop. When the ambient temperature is higher
than the setting temperature, the unit will be
automatically quit the power management feature.
The compressor and (or) fan motor run.
EN
61
