Kaisai KHX-14PY3, Owner'S Manual

Page: 24 / 28

24
Error
code
Error name
Relevant
parts information
Review and resolve
E04
Electric heater over heat
Protection 1. Check the Electrical heating Overheat protector open or not.
2. Check the Electrical heater.
E08
Communication failure
between PCB and display
Communication error
between PCB and DISPLAY
1. Check cable connection of PCB and DISPLAY.
2. Check the software version of PCB and DISPLAY.
E11 HP Protection HP switch is open
1. Check whether showing the error after unit shutdown.
2. Measure the discharge pressure when unit is running.
3. Detect EEV step, suction pressure, inlet/outlet water discharge and suction temp.
4. Release all the gas of the system and refill refrigerant according to the nameplate.
E12 LP Protection LP switch is open
1. Check whether showing the error after unit shutdown.
2. Measure the suction pressure when unit is running.
3. Detect EEV step, discharge pressure, inlet/outlet water discharge and suction temp.
4. Release all the gas of the system and refill refrigerant according to the nameplate.
E19
Primary Anti-freezing
Protection
Ambient temp.≤0°C, A04-
2°C≤ water inlet≤A04°C It is the protection in winter. Once the water temperature rises up to A04+4oC or the
ambient temp is higher than 1, the error code disappears.
E29
Secondary Anti-freezing
Protection
Ambient temp.≤0°C, water
inlet≤A04-2°C
It is the protection in winter. Once the water temperature up to A04+11 oC or the
ambient temp is higher than 1, the error code disappears.
E19
Primary Anti-freezing
Protection
Ambient temp.≤0°C, 2°C ≤
water inlet≤4°C It is the protection in winter. Once the water temperature rises up to 8 oC or the
ambient temp is higher than 1 oC, the error code disappears.
E29
Secondary Anti-freezing
Protection
Ambient temp.≤0°C, water
inlet≤2°C
It is the protection in winter. Once the water temperature up to 15 oC or the ambient
temp is higher than 1
oC, the error code disappears.
E032 Flow Switch Protection Flow switch is open
1. Detect the connection of cables.
2. Detect the flow switch.
3. Detect the water valve is opened or opened fully.
4. Detect the water pump and the filter.
5. Maybe there is some air in the water route.
E051
Compressor Over current
Shutdown Fault
Compressor Over current
1. Check ambient temp. and inlet/outlet water temp.;
2. Turn on the unit. Record and analyze the changing process of high/low pressure,
discharge/suction temp., EEV step, compressor frequency and running current.
3. If they are OK, replace a new compressor driver board.
E065
High water outlet temp.
protection
Check if the water flow is too low and the outlet water whether too high
E081
Communication failure
between PCB and fan
drive board
Communication error
between PCB and fan drive
board
1. Check the connection between PCB and fan board. All of 12V-12V, GND-GND, A-A,
B-B should be closed;
2. If they are closed, turn on the power, then measure the voltage between 12V and
GND on fan board, if higher than 15V or lower than 7V, replace a new fan board.
E103
Fan motor overload
protection
1. Check if the fan motor running well.
2. Detect the current of fan motor.
3. If the current is more than 1A, it means the motor have problem and need
to replace a new one.
4. If the current is less than 1A, it means the motor control module have problem
and nee to replace a new one.
E171 Anti-freezing Protection
inlet water ≤A04°C and the
antifreeze temp ≤
A04-A05°C
1. Check the water flow.
2. Check the outlet water temp sensor.
3. Measure the ambient temp.
4. Detect the connection of cables.
5. Check the record of defrosting, whether the defrosting time is too long
or too often.
7.2.
Error Code Instruction