background image

■  The connection of the device should be done without the system power.

■  The device must be connected as shown in the connection diagram.

■  Do the Pt100 sensor inputs as shown on the back of the unit

■  Do not energize the device without checking all connections using the meter.

Making Connections

Information Panel

The upper part of the screen of the device has an information panel consisting of icons easily 

understood by the user. This panel is always on top of the screen no matter which part the user is 

in. The date, time, device operation status, FAULT status, ALARM status, TRIP status, FAN status 

information are observed in this panel at the same time. The operating status indicator indicates 

OK if the system is normal and returns to exclamation point when an error occurs in the system.

A color LCD display is used in our device to make it much easier and clearer to use. If the 

keys are not pressed for a long time, the device will switch to screen saver mode to extend the life 

of the screen and only step down from the top of the screen with the information panel on top. 

When any key is pressed, the main screen image appears again.

System  Normal

FAN 

14:25

11.10.2016

ALARM

TRIP

TRIP

FAULT (error existing)

TC - PT100

Temperature Controller

Power supply

Un : 24 ... 240V AC 
        50/60Hz / DC
Δn : (0,9 – 1,1) x Un

PT100

red
red
white

PT100

red
red

PT100

red
red

PT100

red
red

ch

1

ch

2

ch

3

ch

4

ALARM

TRIP

FAULT

FAN

K-FAN

SYSTEM

STOP

V

V

white

white

white

The fan icon turns on the screen while the fan is running.
If the screen shows a fan but does not turn, then the unit has gone into a saving mode for cooling.

Over-voltage 
protection
device

Summary of Contents for TC - PT100














Reviews: