background image

Installation instructions

Operation

Kaba c-lever compact 

k2evo703en-2011-05

16

5

Operation

5.1

Operation signals

The acoustic signals may first have to be activated using the Programmer!

Action

Acoustic 

signal

Optical

 signal

Confirmation

Master A/B authorised 
(open programming 
window)

1 x short

1 x green

The acoustic signal sounds if 
the medium is taken out of 
range of the antenna.

Add user medium

1 x short

1 x green

Delete user medium

2 x short

1 x green

Master A/B authorised 
(close programming 
window)

1 x long

1 x green

Authorised medium

1 x short

1 x green

Unauthorised medium

4 x short

4 x red

Master A/B unauthorised 

1 x long

1 x red

Delete subgroup with 
authorised master

2 x short

1 x green

Hold master medium in front 
of antenna for approx. 10 
seconds. 

Soft INI reset with A/B 
structure with authorised 
programming master A or 
with B structure with 
programming master B

2 x short after 
10 secs,
2 x short after 
a further 15 
secs,

Green light on 
presentation 
of card, goes 
out upon 
successful 
initialisation 

2 beeps after 10 seconds 
confirms the complete reset 
of the user media, 2 beeps 
after a further 15 seconds 
confirms the reset of all 
master media. 

Summary of Contents for C-lever compact

























Reviews: