7. Secure using screw through the interior
assembly onto the mouting plate.
8. Install interior assembly on inside mounting
plate.
9. Install exterior lever.
left-out
right-out
10. Install interior lever
left-out
right-out
Warning
5
* Failure to follow these instructions could result in damage to the product and avoid the factory warranty.
* The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment
can cause performance degradation and lessening of security.
* Finish Care: This lockset is designed to provide the highest standard of product quality and performance. Care should
be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner,
caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
IMPORTANT: Do not install batteries untill the lock is completely installed on door.
1
2
3
4
5
6
7
8
9
A.
1
2
3
4
5
6
7
8
9
B.
2
2
2
2
2
2
2
2
2
C.
3
8
6
5
D.
If
Then
and
Forward number sequence
Backward number sequence
Repeat number sequence
3
8
1
9
6
5
1
9
3
8
6
5
Contain existing code sequence
1. Master PIN Code (4~10 digit): Default master pin code is “12345678”, please modify it after installation.
If you forget your master pin code, you can reset your lock back to factory settings.
2. User PIN Code (4~10 digit): User pin codes can be set up through master pin code. Up to 20
user pin code can be stored.
3. Both master and user pin codes don’t support the following combination of numbers.
Master Mode:
The master mode could be entered by entering[**+Master PIN Code+# ] to program the lock.
Master PIN code:
The master pin code is used for programming and for feature settings.
Manual Mode:
Manual mode is designed for high traffic doors, when Manual mode is enabled, the door will be openable without PIN
code or key, Manual mode could be disabled temporary by press and hold any key on keypad for 2 seconds from outside.
Shutdown Time:
The lock will shutdown for a default of 3 mins and not allow operation after the wrong code entry limit (10 times) has
been met. When the unit is in shutdown, the light will flash when you are trying to use keypad.
Silent Mode:
The beeper will not make any voice.
Status indicators:
Located on exterior assembly.
User PIN code:
The user pin code operates the lock. Maximum capacity of user pin codes is 20.
Reset button:
After reset operation, the lock will be restored to factory default settings, all user credentials will be deleted. Refer to reset
guide.
Definitions
6
7
Factory Default
Settings
Master PIN Code
Beeper
Wrong Code Entry Limit
Shutdown Time
Enabled
10 times
3 mins
12345678
Factory Default settings
8
Lock Operation
Change Master PIN code
1.Touch the screen with your hand to activate.
2.Enter “*”twice and the 4-10 digit Master PIN Code followed by “#”.
3.Enter “1”to change Master PIN Code.
4.Enter new 4-10 digit Master PIN Code followed by “#”.
5.Repeat step 4 one more time.
Before changing default Master PIN Code,all other setting menu will be disabled.You have te change Master PIN Code
first,the do other lock settings.
Add up User PIN codes
1.Touch the screen with your hand to activate.
2.Enter“*”twice and the Master PIN Code followed by “#”.
3.Enter “2”.
4.Enter “1”, add user PIN code.
5.Enter new User PIN code followed by “#”.
6.Repeat step 5 one more time.
7.To continue adding users,do previous steps 4-5 again.
When registering User PIN codes,the code must be entered within 10 seconds or time expires.No matter setting
succeed or failed,the process won’t completedand stay at current stage,you can press “*”to return to previously menu.
When deleting User PIN codes,the User Number must be entered within 10 seconds ot time expires.No matter setting
succeed or failed,the process won’t completed and stay at current stage,you can press “*” to return to previously
menu. Deleting all User PIN codes could be done only by reseting the lock to fatory default settings.
Delete User PIN codes
1.Touch the screen with your hand to activate.
2.Enter“*”twice and the Master PIN Code followed by “#”.
3.Enter “3”, Lock Response: key“1”light up.
4.Enter “1” for deleted PIN code Voice guide.
5.Enter the PIN code, and confirm with“#”.
6.To continue deleting users,do previous steps 1-4 again.
Silent Mode(Speaker enable/disable)
Silent Mode feature can only be programmed through the Master PIN code or APP.
1.Touch the screen with your hand to activate.
2.Enter“*”twice and the Master PIN Code followedby “#”.
3.Enter “5”to set up languages.
4.Enter “1 or 2 or 3 or 4 or 5”to select voice guide language(Silent Mode disable),enter“6” to enable Silent Mode.
Bluetooth settings(only for RX-D)
Bluetooth feature can be programmed through the Master PIN code or APP.Bluetooth is disabled in
factory default setting.
1.Touch the screen with your hand to activate.
2.Enter“*”twice and the Master PIN Code followed by “#”.
3.Enter “7”to enter Bluetooth settings.
4.Enter “1”to enable Bluetooth,Bluetooth will work continuously after opration.
5.Enter “2”to disabled Bluetooth,Bluetooth will shut down in 2 mins after touch keypad lights off for engrgy saving, it
will back to work when touch keypad wakes up.
Function extension settings (only for RX-D)
Network features are included in function extension,can only be programmed through the Master PIN
code.
1. Touch the screen with your handto activate.
2. Enter “*" twice and the master PIN Code followed by “#".
3. Enter “8" to join network.
4. Enter “1" to log in network.
5. Enter “2" to log out network.
If the lock is connected to a network controller,it is recommended that it is programmed through the centralized user
interface(PC or hand-held device)to ensure communication between the lock and the controller.
How to use
9
Normal
In Auto re-lock mode, the bolt will extend
out automatically in 5 seconds after unlocking.
1.Unlock the door from outside Master/User pin
code or key.
Lock the door
Unlock the door
Press any key on keypad for 2 seconds.
Manual Mode
User can prevent pin code exposure from stangers by entering random digits before or after pin code.
Operation on lock
1. Open battery box and find the reset button.
2. User a sharp thing to press and hold the reset button.
3. Keep holding the reset button for 5 seconds untill hearing voice guide.
4. After that all user data and settings will be deleted.
Unlock with Fake PIN code
Reset to factory default settings
83618
137192
14710
password
Random digits
Lock the door from outside
Congratulations, you have installed your new lock, now please follow instructions to program your lock.
Manual Mode Switch
1. Enable: Move the switch to position to
enable manual mode.
2. Disable: Move the switch to position to
disable manual mode.
Manual mode
