background image

331551-002  

 

– 3 – 

I) INTRODUCTION

Thank you for purchasing a John Wood Oil Fired Water 
Heater.

 Properly installed and maintained, it will provide years 

of trouble free service.
This Oil Fired Water Heater is suitable for potable water 
heating and space-heating applications but not for space 
heating only applications. It is your responsibility to ensure 
that the correct size of your water heater was determined by 
calculations that included consideration of heat loss.

 Consumer Responsibilities

This manual has been prepared to acquaint you with the 
installation, operation and maintenance of your oil fired water 
heater and provide important safety information in these 
areas. It is your responsibility to ensure that your water heater 
is properly installed and cared for.
FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS 
MANUAL MAY RESULT IN SERIOUS BODILY INJURY 
AND/OR PROPERTY DAMAGE. THOROUGHLY READ 
AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU 
ATTEMPT TO INSTALL, OPERATE OR MAINTAIN THIS 
HEATER.
Installation and service requires trade knowledge in the areas 
of plumbing, electricity, venting, air supply and oil supply. If 
you lack these skills or have difficulty understanding these 

instructions, you should not proceed. Enlist the help of a 
qualified service technician to install this water heater.

Examples of qualified service technicians include those 
trained in the plumbing and heating industry, local oil supply 
personnel or an authorized service person.

The manufacturer and seller of this water heater will not 
assume any liability for any property damage, personal injury 
or death resulting from improper sizing, installation or failure 
to comply with these instructions.

The warranty on this water heater is in effect only when the 
water heater is installed and operated in accordance with 
these instructions. An identifying data plate can be found at 
the front of your water heater. When referring to your water 
heater, always have the information listed on the data plate 
readily available.

Protect your warranty: Regularly service your water heater as 
directed in the "Maintenance" section of this manual.
Retain your original receipt as proof of purchase.

Do not discard this manual. You or future users of this water 
heater will need it for reference.

Your safety and the safety of others is extremely important in the installation, use and servicing of this water heater.
Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and 
others of a potential injury hazard. Read and obey all safety messages and instructions throughout this manual. It is very important 
that the meaning of each safety message is understood by you and others who install, use or service this water heater.

This is the safety alert symbol. It is used to alert you 
to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

CAUTION used without the safety alert 
symbol indicates a potentially hazardous 
situation which, if not avoided, could 
result in property damage

CAUTION indicates a potentially 
hazardous situation which, if not avoided, 
could result in minor or moderate injury.

WARNING indicates a potentially 
hazardous situation which, if not avoided, 
could result in death or injury.

DANGER indicates an imminently 
hazardous situation which, if not avoided, 
will result in death or injury.

CAUTION

 WARNING

 CAUTION

 DANGER

All safety messages will generally tell you about the type of hazard, what can happen if you do not follow the safety message 
and how to avoid the risk of injury.
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances 
known to the State of California to cause cancer, birth defects or other reproductive harm and requires businesses to warn of 
potential exposure to such substances.
This product contains a chemical known to the State of California to cause cancer, birth defects or other reproductive harm. 
This appliance can cause low level exposure to some of the substances listed in the Act.

This product is certified to comply with a maximum weighted average of 0.25% lead content as required in some areas.

Summary of Contents for JW F657





























Reviews: