JVC TH-M65 Service Manual Download Page 2

Page: 2 / 42

1-2 (No.MB112)

SPECIFICATION

Designs & specifications are subject to change without notice.

Center unit (XV-THM65)

Audio

Audio input sensitivity/Impedance (at 1 kHz), Total Harmonic Distortion 0.02 %
NOTE : This value is measured at System cord CONNECTOR for reference.

Analog input

AUDIO IN (VCR)

290 mV/47 K

Ω

MIC

4.3 mV/600

Ω

Digital input*

DIGITAL IN (DBS)

-21 dBm to -15 dBm

(OPTICAL)

(660 nm E30 nm)

* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency - 32 kHz, 44.1 kHz, 48 kHz)

Digital output

DIGITAL OUT

-21 dBm to -15 dBm

(OPTICAL)

(660 nm E30 nm)

Video

Color System

NTSC/PAL selectable

Horizontal Resolution

500 lines

Signal-to-Noise Ratio

64 dB

Video output level

Composite

1.0 V(p-p)/75

Ω

S-video-Y

1.0 V(p-p)/75

Ω

S-video-C

0.286 V(p-p)/75

Ω

Component-Y

1.0 V(p-p)/75

Ω

Component-PB/PR

0.7 V(p-p)/75

Ω

Video input sensitivity/
Impedance (VCR IN)

Composite

1.0 V(p-p)/75

Ω

S-video-Y

1.0 V(p-p)/75

Ω

S-video-C

0.286 V(p-p)/75

Ω

Tuner

Tuning Range

87.50 MHz to 108.00 MHz

531 kHz to 1 602 kHz (at 9 kHz intervals)
530 kHz to 1 600 kHz (at 10 kHz intervals)

General

Power Requirements

AC 110 - 230 V , 50 Hz/60 Hz

Power Consumption

20 W (at operation) 1.6 W (in standby mode)

Dimensions (W

400 mm

85 mm

386 mm

Mass

4.6 kg

Subwoofer (SP-PWM65)

Amplifier

Front/Center/Surround

80 W per channel, RMS at 6

Ω

at 1 kHz, with 10 % total harmonic distortion.

Subwoofer

120 W, RMS at 4

Ω

at 100 Hz, with 10 % total harmonic distortion.

Speaker

Speaker unit

20 cm Bass-reflex, Magnetically Shielded

Frequency Range

25 Hz to 200 Hz

General

Power Requirements

AC 110 V/127 V/220 - 230 V selectable with the voltage selector, 50 Hz/60 Hz

Power Consumption

150 W (at operation) 0 W (in standby mode)

Dimensions (W

235 mm

355 mm

492 mm

Mass

13.0 kg

Satellite Speakers (SP-THM65F)

Speakers

5.5 cm

2 Bass-reflex, Magnetically Shielded

Power Handling Capacity

80 W

Impedance

Ω

Frequency Range

90 Hz to 20 kHz

Dimensions (W

250 mm

1 103 mm

250 mm

Mass

3.77 kg

Center Speaker (SP-THM65C)

Speakers

5.5 cm

2 Bass-reflex, Magnetically Shielded

Power Handling Capacity

80 W

Impedance

Ω

Frequency Range

90 Hz to 20 kHz

Dimensions (W

258 mm

75 mm

81 mm

Mass

0.95 kg

Summary of Contents for TH-M65











































Search results

Summary of Contents for TH-M65

Reviews:

Related manuals for TH-M65

Brands by name

Popular brands

JVC TH-M65, Service Manual

Search results

Summary of Contents for TH-M65

Reviews:

Related manuals for TH-M65

Brands by name

Popular brands