Masterpage:Right+
EN
65
Filename [DVM70S_12Editing.fm]
EDITING
Page 65
Monday, 27 December 2004 14:08
This function allows you to record new audio, without erasing the
original audio, on a DV tape that was recorded with
A
DV AUDIO
REC
B
set to
A
12BIT
B
(
A
pg. 72).
1
Connect an audio device to the unit’s [AUDIO] input connectors
on the front panel.
●
When using a monaural audio device, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
2
Load a Mini DV cassette with the erase protection switch set to
A
REC
B
.
3
Press
DV/HDD/DVD
on the unit repeatedly or
DV
on the remote
so that the DV lamp lights up on the unit.
4
Press
PR +/–
on the remote control or
INPUT SELECT
JK
on
the unit to select
A
F-1
B
.
5
Start playback slightly before the actual point from where you
wish to start dubbing.
6
Press
W
to pause playback.
7
Press
AUDIO DUB.
to engage the audio dubbing mode.
●
Your unit enters the Audio Dubbing Pause mode.
●
To perform Audio Dubbing with audio mixing, press
AUDIO
to
select
A
L
W
X
R
B
at this point. When using the DV deck as the
recording deck, also make sure that
A
AUDIO MODE
B
is set to
A
SOUND1
B
(
A
pg. 72).
* Audio Dubbing with audio mixing is not possible if you are using a
monaural audio component, or if you don’t have an audio mixer.
8
Engage the audio device’s playback, then press
I
to start the
tape in the unit. Audio dubbing starts at this point.
●
To stop dubbing temporarily, press
W
. Press
I
to resume
dubbing.
9
Press
o
on the unit, then stop playback on the audio device to
end the audio dubbing.
NOTES:
●
Once the Audio Dubbing starts, you cannot use the other deck.
●
When monitoring the audio dubbed sound on the DV deck, set
A
AUDIO MODE
B
to
A
SOUND2
B
(
A
pg. 72).
●
Audio Dubbing is also possible with the [L-1 IN/OUT] or [L-2 IN/
DECODER] connector on the rear panel. When using these 21-
pin SCART connectors, be sure to select the correct input mode
(
A
L-1
B
or
A
L-2
B
) in step
4
.
●
When playing back an audio dubbed Mini DV tape on the DV
deck, set
A
AUDIO MODE
B
to
A
SOUND2
B
(
A
pg. 72).
●
Audio dubbing is not possible using the [DV IN/OUT] connector.
●
Audio dubbing is not possible on a blank portion of the tape.
Audio Dubbing (DV Deck Only)
ATTENTION:
You cannot perform Audio Dubbing on a tape that was recorded
with
A
DV AUDIO REC
B
set to
A
16BIT
B
(
A
pg. 72), on a tape that
was recorded at the
A
LP
B
speed, or on a blank tape.
AUDIO OUT
Audio cable
(not supplied)
Recorder
Mixer output
To [AUDIO]
input
Your unit
AUDIO DUB.
Original sound
Audio mixer
[AUDIO OUT]
Recorder
Your unit
To
[AUDIO]
input
CD player, etc.
CD player, etc.
INPUT SELECT
JK
INPUT SELECT
JK
AUDIO DUB.
●
Slide the
TV/CABLE/SAT/DVD
switch to
DVD
.
DVM70S_00.book Page 65 Monday, December 27, 2004 2:08 PM
