JVC RX-DV31SL Service Manual Download Page 9

Page: 9 / 66

(No.22023)1-9

3.1.8 Removing the amp. board

(See Fig.11)

• Prior to performing the following procedures, remove the top

cover and rear panel.

(1) From the top side of the main body, disconnect the wire

from the connector CN201 on the amp. board.

(2) Remove the screw

attaching the earth wire to the heat

sink barcket.

(3) Remove the four screws

attaching the amp. board.

(4) Disconnect the connector CN202 on the amp. board.
(5) Lift the amp. board and disconnect the wire from the con-

nector CN231 on the main board.

(6) Disconnect the parallel wire from the connector CN241 on

the main board and take out the amp. board.

Fig.11

3.1.9 Removing the heat sink

(See Fig.12)

• Prior to performing the following procedures, remove the top

cover, rear panel and amp. board.

(1) Remove the screw

attaching the H.sensor board.

(2) Remove the five screws

attaching the IC bracket, heat

sink bracket and heat sink.

Fig.12

3.1.10 Removing the power ICs

(See Fig.13)

• Prior to performing the following procedures, remove the top

cover, rear panel, amp. board and heat sink.

(1) From the reverse side of the amp. board, remove the sol-

ders from the soldered points

attaching the power ICs to

the amp. board.

Fig.13

CN201

Earth wire

CN202

Main board

Amp. board

CN231

CN241

Heat sink bracket

H. sensor board

Heat sink bracket

Heat sink

IC bracket

Amp. board

Power ICs solbered points

Summary of Contents for RX-DV31SL



































































Search results

Summary of Contents for RX-DV31SL

Reviews:

Related manuals for RX-DV31SL

Brands by name

Popular brands

JVC RX-DV31SL, Service Manual

Search results

Summary of Contents for RX-DV31SL

Reviews:

Related manuals for RX-DV31SL

Brands by name

Popular brands