21
From the remote control:
1. Press FM/AM.
• Each time you press the button, the band alternates between
FM and AM.
2. Press TUNING UP or TUNING DOWN repeatedly until you
find the frequency you want.
• Pressing TUNING UP increases the frequency.
• Pressing TUNING DOWN decreases the frequency.
Using Preset Tuning
Once a station is assigned to a channel number, the station can be
quickly tuned in. You can preset up to 30 FM and 15 AM stations.
To store the preset stations
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
2
again.
On the front panel ONLY:
1. Tune in the station you want to preset
(see “Tuning in to Stations Manually”
on the left).
• If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the
FM Reception Mode” on page 22.
2. Press MEMORY.
The channel number position starts flashing on the display for
about 10 seconds.
3. Press FM/AM PRESET
5
or
∞
to select a
channel number while the channel number
position is flashing.
4. Press MEMORY again while the selected channel
number is flashing on the display.
The selected channel number stops flashing.
The station is assigned to the selected channel number.
5. Repeat steps 1 to 4 until you store all the stations
you want.
To erase a stored preset station
Storing a new station on a used number erases the previously stored
one.
Receiving Radio Broadcasts
You can browse through all the stations or use the preset function to go immediately to a particular station.
Tuning in to Stations Manually
1. Press FM or AM to select the band.
The last received station of the selected band is tuned in.
2. Press FM/AM TUNING
5
or
∞
repeatedly until
you find the frequency you want.
• Pressing FM/AM TUNING
5
increases the frequency.
• Pressing FM/AM TUNING
∞
decreases the frequency.
Notes:
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
• When you hold and then release the button in step
2
, the frequency
keeps changing until a station is tuned in.
VOLUME
TUNED STEREO
LINEAR PCM
L
SUBWFR
R
ANALOG
SPEAKERS 1
VOLUME
TUNED STEREO
LINEAR PCM
L
SUBWFR
R
ANALOG
SPEAKERS 1
VOLUME
TUNED STEREO
LINEAR PCM
L
SUBWFR
R
ANALOG
SPEAKERS 1
VOLUME
TUNED STEREO
LINEAR PCM
L
SUBWFR
R
ANALOG
SPEAKERS 1
RX-8030V AUDIO/VIDEO CONTROL RECEIVER
Setting the AM Tuner Interval Spacing
Some countries space AM stations 9 kHz apart, and other countries
use 10 kHz spacing. Select the appropriate interval spacing setting to
receive the AM broadcasting in your area.
• 9 kHz interval spacing is the initial setting.
On the front panel ONLY:
1 Turn off the unit.
• Be sure that the unit is plugged into a wall outlet.
2 Change the interval spacing.
To set the AM tuner to the 10 kHz spacing:
Hold down FM/AM TUNING
5
and press
STANDBY/ON.
“10k STEP” appears on the display for a while.
To set the AM tuner to the 9 kHz spacing:
Hold down FM/AM TUNING
∞
and press
STANDBY/ON.
“9k STEP” appears on the display for a while.
The unit is turned on with the interval spacing changed.
RX-8030V AUDIO/VIDEO CONTROL RECEIVER
RX-8030V AUDIO/VIDEO CONTROL RECEIVER
Remote
NOT
Remote
NOT
21_22_8030[UJ]f.p65
03.6.17, 8:21 PM
21
