JVC RX-7022RBK Instructions Manual Download Page 37

Page: 37 / 46

Operating JVC’s Audio/Video Components

You can use the remote control to operate other JVC’s
components.

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using this remote control:
• You need to connect JVC’s audio components through the COMPU

LINK-4 (SYNCHRO) jacks (see page 31) in addition to the
connections using cables with RCA pin plugs (see pages 6 and 7).

• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not

operate that source. To operate a source with the remote control,
the source must be selected using source selecting buttons on the
remote control.

• To operate the cassette deck or CD recorder using the COMPU

LINK remote control system, set the source name correctly. (See
page 11.)

• Refer also to the manuals supplied with your audio components.

Sound Adjustment

You can always use the following buttons:

SURROUND ON/OFF

: Turn on or off the Surround modes.

SURROUND MODE

: Select the Surround modes.

After pressing SOUND, you can use the following buttons for sound
adjustment:

SUB/–

: Adjust the subwoofer output level.

/–

: Adjust the center speaker output level.

REAR•L +/–

: Adjust the left rear speaker output level.

REAR•R +/–

: Adjust the right rear speaker output level.

EFFECT

: Select the DAP effect level.

TEST

: Turn on or off the test tone output.

Note:

After adjusting sounds, press the corresponding source selecting
button or CONTROL to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.

Tuner

You can always use the following buttons:

FM/AM

: Alternate between FM and AM.

After pressing FM/AM, you can use the following buttons for tuner
operations:

1 – 10, +10

: Select a preset channel number directly.

• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 20, press +10, then 10.

/–

: Tune into stations.

FM MODE

: Change the FM reception mode.

CONTROL

+
−

7/P

+10

BASS BOOST

EFFECT

MENU

ENTER

TEST

DIMMER

MUTING

TV VOL

/REW

FF/

VOLUME

CATV/DBS
CONTROL

TV/VIDEO

REC

TUNING

PAUSE

RETURN

FM MODE

100+

CONTROL

A/V CONTROL RECEIVER

RM-SRX7022U

REMOTE CONTROL

CATV/DBS

VCR

AUDIO

SURROUND

MODE

INPUT

ON/OFF

DVD MULTI

DVD

TAPE/CDR

TREBLE

TV/DBS

VCR

PHONO

FM/AM

BASS

SURROUND

ANALOG/DIGITAL

SLEEP

−

– SUB

– REAR • R +

– REAR • L +

–

−

SOUND

When you press one of the following buttons, the remote
control operation mode appears on the display window.

A/V CONTROL RECEIVER

Ex.: When you press CD.

Buttons on the Remote Control

Remote Control Operation Mode

FM/AM

TUNER

PHONO

TAPE/CDR

TAPE

DVD

DVD MULTI

DVD

TV/DBS

VCR

CATV/DBS CONTROL

DBS

CONTROL

VCR or TAPE or CDDSC

SOUND

EN30-42.RX-7020V[A]3

02.4.17, 5:16 PM

Summary of Contents for RX-7022RBK















































Search results

Summary of Contents for RX-7022RBK

Reviews:

Related manuals for RX-7022RBK

Brands by name

Popular brands

JVC RX-7022RBK, Instructions Manual

Search results

Summary of Contents for RX-7022RBK

Reviews:

Related manuals for RX-7022RBK

Brands by name

Popular brands