manualshive.com logo in svg

JVC MX-GA77, Service Manual

Share
Download
JVC MX-GA77 Service Manual Download Page 16

MX-GA77

1-16

Slide the plastic cover in the direction of the arrow, 
and remove the three claws. Then remove the 
plastic cover.

Remove the two screws D fixing the motor.
Be careful to grease's splash when the drive belt 
comes off.

Unsolder the motor terminal.

1.

2.

3.

Removing the motor        (See Fig. 4 to 6)

Unsolder the four solder parts a and the four solder 
parts b.

Remove the two screws E attaching the mecha. 
board.

1.

2.

Removing the mechanism board
                                                   (See Fig. 5)

Remove the cut-washer at c from the capstan shaft, 
then remove the flywheel.
When reassembling the flywheel, be sure to use new 
washers as they cannot be reused.

1.

Removing the flywheel
                                        (See Fig. 7 and 9)

Fig.5

Fig.4

Drive belt

Drive belt

Drive belt

Motor

Motor
terminal

Plastic cover

Claw

Motor

c

FR belt

FR belt

Washer

Flywheel

Capstan

washer

Mecha. board

Fig.6

Fig.7

Fig.8

Fig.9

Sleeve

D

E

E

Solder

part a

Solder

part a

Solder
part b

Summary of Contents for MX-GA77


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands