manualshive.com logo in svg

JVC MX-GA77, Service Manual

Share
Download
JVC MX-GA77 Service Manual Download Page 11

1-11

MX-GA77

Prior to performing the following procedure, remove 
the CD tray.

Remove the screw A  attaching the sensor board on 
the CD tray.

Remove the sensor board releasing the two tabs a.

Disconnect the harness from the connector CW1 on 
the sensor board.

1.

2.

3.

Removing the sensor board    (See Fig.5)

Prior to performing the following procedure, remove 
the CD tray and sensor board.

Remove the screw B attaching the turn tray. Detach 
the turn tray from the base tray.

Pull outward the tab b attaching the turn tray motor  
on the base tray and detach the turn tray motor.

1.

2.

Removing the turn tray motor
                                         (See Fig.6 and 7)

Introductory notes:
Base tray + Turn tray = CD tray

Fig.7

Fig.6

Tab a

Tab b

Sensor board

CW1

Turn tray

Base tray

CD tray (reverse side)

Base tray (upper side)

B

Turn tray motor

A

Fig.5

Summary of Contents for MX-GA77


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands