manualshive.com logo in svg

JVC MX-GA77, Service Manual

Share
Download
JVC MX-GA77 Service Manual Download Page 12

MX-GA77

1-12

Prior to performing the following procedure, remove 
the CD tray.

Detach the belt from the pulley on the upper side of 
the CD changer unit (Do not stain the belt with 
grease).

Disconnect the card wire from the pickup unit 
connector on the under side of the CD changer unit.

  Attention : Solder is put up before the card wire is 
                    removed from the pick-up unit 
                    connector on the CD mechanism
                    assembly. 
                    (When the card wire is removed without 
                     putting up solder, the CD pick-up unit
                    assembly might destroy.) 

Disconnect the motor wire harness from connector 
on the CD board.

Remove the screw C attaching the switch board and  
release the two tabs e attaching the switch board 
outward and detach the switch board.

Remove the two screws D attaching the CD board. 
First release the two tabs f and two tabs g attaching 
the motor, then release the CD board.

If the tabs f and g are hard to release, it is 
recommendable to unsolder the two soldered parts 
on the motor terminal of the CD board. 

1.

2.

3.

4.

5.

Removing the belt, the CD board and the 
switch board                   (See Fig.8 and 9)

Soldering

Card wire

Picup unit
connector

Fig.9

Fig.8

Belt

CD changer unit

D

CD board

Tabs g

Tabs f

Soldered parts

Motor

Switch board

C

CW3

Tabs e

CD mechanism board

motor connecter

Pickup unit connector

Summary of Contents for MX-GA77


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands