8
2 Preparation
Unpacking the TV
Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
Thank you
for purchasing your new JVC TV.
Your new TV has many features and incorporates the latest technology to enhance your viewing
experience. We recommend that you spend some time reading this instruction manual so that you fully
understand these features. You will also find some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.
Chapter
2
Remote Control /
AAA Batteries x 2
Stand screws x8
Instruction Manual
YPbPr Cable
Quick Start Guide
FAV Cable
Instruction Manual
40" LED Smart HD TV
with built-in DVD player
LT-40C755
GB
For help and support call
UK: 0344 561 1234 • Ireland: 1890 818 575
• Do not connect the TV to the mains supply until you have completed all the connections.
• Always disconnect the TV from the mains socket when not in use for a long period of time.
• The
button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.
To completely disconnect the mains power, please remove the mains plug from the mains socket.
Please inspect your TV for damage after unpacking. If you do notice any damage please consult your dealer.
Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.
Unpacking
1
1. Connect one end of the RF coaxial cable to the aerial socket on the wall
and the other end of the cable to the
ANT
socket on the back of your TV.
2. Plug the TV into a mains socket and switch on at the mains.
3. In standby mode, press the button on the remote control to turn the
TV on. The LED indicator will flash for a few seconds then the TV will
switch on.
Connecting the Aerial and Turning on the TV
4
1. Slide open the battery compartment on the back of the remote control.
Operating Your Remote Control
2
Thank you
for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful first time installation.
The latest eco-friendly power-saving technology will switch off the TV if
it is left on and idle for 4 hours. Please refer to “Auto Standby” under the
“Time Settings” section of the instruction manual for more detail.
Quick Start Guide
40" LED Smart HD TV
with built-in DVD player
LT-40C755
2. Insert two AAA size batteries. Make sure to match the (+) and ( - )
ends of the batteries with the (+) and ( - ) ends indicated in the battery
compartment.
3. Slide the battery compartment cover back into place. Make sure it clicks
into place.
Optional
If you want to connect to the internet via a wired connection
then connect your ethernet cable to the
LAN
socket.
SCART
SPDIF
Coax.OUT
VGA
ANT
.
HDMI 1
(ARC
)
HDMI 2
HDMI 3
LAN
SCART
SPDIF
Coax.OUT
VGA
ANT
.
HDMI 1
(ARC
)
HDMI 2
HDMI 3
LAN
RF coaxial cable
(not included)
Slide under
the lip
SCART
SPDIF
Coax.OUT
VGA
ANT
.
HDMI 1
(ARC
)
HDMI 2
HDMI 3
LAN
The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object,
or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because
the screen could crack.
Fitting the Stand to the TV
3. Ensure the TV is switched off and not connected to the mains power supply.
4. Lay the TV down on a flat surface ideally on the edge of a table so the base of the
TV slightly overhangs the edge of the table, with the back side facing up. Please
make sure a soft cushioned material (such as a dry bath towel or thick piece of
foam) is placed beneath the screen.
5. Slide the stand under the lip, the neck will fit snugly over the screw holes. Then
screw the stand to the TV using the 4 screws supplied.
Fitting the Stand Neck and Base Together
1. Fit the neck onto the base.
2. Using 4 of the supplied screws, screw the neck to the base.
Installing the Base Stand
3
Slide under
the lip
Table
Cushioned
material
TV
TV Stand Neck
TV Stand Base
Remote Control/
AAA Batteries x2
Screws x 8
YPbPr Cable
FAV Cable
Instruction Manual
Quick Start Guide
LT-40C755_QSG.indd 1
23/01/2015 11:19
TV
TV Stand Neck
TV Stand Base
LT-40C755_IB.indd 8
27/01/2015 17:51
Summary of Contents for LT-40C750
Page 57: ...56 10 Technical Information and Help ...
Page 60: ......
