JVC KD-SX997R Service Manual Download | Manualshive

Page: 26 / 55

background image

KD-SX998R,KD-SX997R

1-26 (No.49819)

3.4 Maintenance of laser pickup

(1) Cleaning the pick up lens

Before you replace the pick up, please try to clean the lens
with a alcohol soaked cotton swab.

(2) Life of the laser diode

When the life of the laser diode has expired, the following
symptoms will appear.
• The level of RF output (EFM output:ampli tude of eye

pattern) will be low.

(3) Semi-fixed resistor on the APC PC board

The semi-fixed resistor on the APC printed circuit board
which is attached to the pickup is used to adjust the laser
power.Since this adjustment should be performed to match
the characteristics of the whole optical block, do not touch
the semi-fixed resistor.
If the laser power is lower than the specified value,the laser
diode is almost worn out, and the laser pickup should be re-
placed. If the semi-fixed resistor is adjusted while the pick-
up is functioning normally,the laser pickup may be
damaged due to excessive current.

3.5 Replacement of laser pickup

Is RF output
1.0 0.35Vp-p?

Replace it.

NO

YES

O.K

Turn off the power switch and,disconnect the
power cord from the ac outlet.

Replace the pickup with a normal one.(Refer
to "Pickup Removal" on the previous page)

Plug the power cord in,and turn the power on.
At this time,check that the laser emits for
about 3seconds and the objective lens moves
up and down.
Note: Do not observe the laser beam directly.

Play a disc.

Check the eye-pattern at RF test point.

Finish.

«
...
24
25
26
27
28
...
»

Summary of Contents for KD-SX997R
























































Reviews:

No comments

Related manuals for KD-SX997R

Brand: Labgear Pages: 14

Brand: FAAC Pages: 2

Brand: Icom Pages: 24

Brand: Xomax Pages: 18

XM2GO - MyFi Portable Satellite Radio

Brand: XM Satellite Radio Pages: 15

Portable CD Player

Brand: Jensen Pages: 12

Stage-100 Series

Brand: Parallel Audio Pages: 12

Brand: Strong Pages: 15

Brand: Minicom Pages: 4

Brand: Icom Pages: 101

Brand: Magtek Pages: 42

C Prox WAVE500-2B

Brand: Quantek Pages: 4

Brand: JCM Technologies Pages: 2

XTT909-1-0-GB-XX

Brand: impro Pages: 8

Brand: Rosen Pages: 17

Brand: DIGITAL YACHT Pages: 4

Digital Freeview Receiver

Brand: Tevion Pages: 2

Brand: WiPath Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands